Loren Data Corp.

'

  
COMMERCE BUSINESS DAILY ISSUE OF NOVEMBER 22, 2000 PSA #2732
SOLICITATIONS

A -- EXTENDED RANGE GUIDED MUNITIONS COMPONENTS

Notice Date
November 20, 2000
Contracting Office
Dahlgren Division, Naval Surface Warfare Center, 17320 Dahlgren Road, Dahlgren, VA 22448-5100
ZIP Code
22448-5100
Solicitation Number
N00178-01-R-1008
Response Due
December 4, 2000
Point of Contact
SD11 Branch at (540)653-7478
E-Mail Address
SD11 Branch is POC for N00178-01-R-1008 (sd11@nswc.navy.mil)
Description
This is a combined synopsis/solicitation for commercially machined items prepared in accordance with the format in FAR Subpart 12.6, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; proposals are being requested and a written solicitation will not be issued. Simplified Acquisition Procedures will be used in accordance with FAR 13.5. The Naval Surface Warfare Center, Dahlgren Division (NSWCDD) intends to procure on a firm-fixed price basis Type "P" Extended Range Guided Munitions (ERGM) components with Option Items for additional Type "P" and "N" components. The solicitation number is N00178-01-R-1008 and is a request for proposal (RFP). The solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular 97-20 and DFARS Change Notice 20001025 dated 25 Oct 2000. FAR and DFARS provisions and clauses may be accessed at http://www.arnet.gov/far/ and http://www.acq.osd.mil.dp/dars/dfars.html respectively. The North American Industry Classification System code is 332710, 500 employees. This requirement is 100 percent set-aside for small business and FAR 52.219-6 Notice of Total Small Business Set-Aside (JUL 1996) is applicable. The following Type "P" ERGM base items are required: CLIN 0001, Obturator, Aft, ERGM Slug in accordance with Drawing 77799 Rev A, 75 EA; CLIN 0002, Obturator, Forward, ERGM Slug in accordance with Drawing 77800 Rev F, 75 EA; CLIN 0003, Shell, Fwd, 5-Inch Inert ERGM in accordance with Drawing SK77830 Rev E, 75 EA; CLIN 0004, Ramp, Obturator, 5-Inch Inert ERGM in accordance with Drawing SK77828 Rev B, 75 EA; CLIN 0005, Bulkhead, Inert, 5-Inch/62 Caliber ERGM in accordance with Drawing SK77829 Rev C, 75 EA; CLIN 0006, Body, Rocket Motor, 5-Inch Inert ERGM in accordance with Drawing SK77827 Rev B, 75 EA; CLIN 0007 Plate, Pusher, 5-Inch Inert ERGM in accordance with Drawing SK77826, 75 EA; CLIN 0008, Weld Assembly, Tail Fin, 5 Inch/62 Caliber ERGM in accordance with Drawing SK77822 Rev A, 75 EA: CLIN 0009, Aft Closure, 5-Inch Inert, ERGM in accordance with Drawing SK77823 Rev B, 75 EA; CLIN 0010, Fin, Tail, Inert, 5 Inch/62 Caliber ERGM in accordance with Drawing SK77824-1, 75EA; CLIN 0011, Fin, Tail, Inert, 5 Inch/62 Caliber ERGM in accordance with Drawing SK77824-2, 75EA; CLIN 0012, Retainer, Tail Fin, 5 Inch Inert ERGM in accordance with Drawing SK77825, 75 EA; CLIN 0013, 1 LOT, Data in accordance with CDRLS A001, A002, not separately priced. Note: the drawings in CLINS 0009-0012 are part of the weld assembly drawing in CLIN 0008. The contractor shall provide a Material Certification Report and a Gaging Inspection Report in accordance with CLINS 0013, 0026, and 0043. One hundred percent (100%) of the components shall have a gaging inspection to assure dimensional compliance with the drawings. The inspection information provided shall identify the drawing number, part serial number, and the measured dimensions. All materials shall be certified to meet the material specification as well as the chemical and physical properties of the material. Option Items are as follows: Option I, CLINS 0014 0026 are Type "P" components and Option II, CLINS 0027 0042 are Type "N" components with SUBCLINS (AA AE) established to differentiate pricing dependent upon various possible ordered quantities (1-10, 11-20, 21-30,31-40, 41-50). A complete breakdown of the schedule inclusive of SUBCLIN quantities can be downloaded by visiting the NSWCDD business opportunities website at http://www.nswc.navy.mil/supply and accessing the attachment which is a PDF file. CLINS 0026 and 0043 are data in accordance with CDRLS A001 and A002. CLIN 0014, Obturator, Aft, ERGM Slug in accordance with Drawing 77799 Rev A; CLIN 0015, Obturator, Forward, ERGM Slug in accordance with Drawing 77800 Rev F; CLIN 0016, Shell, Fwd, 5-Inch Inert ERGM in accordance with Drawing SK77830 Rev E; CLIN 0017, Ramp, Obturator, 5-Inch Inert ERGM in accordance with Drawing SK77828 Rev B; CLIN 0018, Bulkhead, Inert, 5-Inch/62 Caliber ERGM in accordance with Drawing SK77829 Rev C; CLIN 0019, Body, Rocket Motor, 5-Inch Inert ERGM in accordance with Drawing SK77827 Rev B; CLIN 0020 Plate, Pusher, 5-Inch Inert ERGM in accordance with Drawing SK77826; CLIN 0021, Weld Assembly, Tail Fin, 5 Inch/62 Caliber ERGM in accordance with Drawing SK77822 Rev A; CLIN 0022, Aft Closure, 5-Inch Inert, ERGM in accordance with Drawing SK77823 Rev B; CLIN 0023, Fin, Tail, Inert, 5 Inch/62 Caliber ERGM in accordance with Drawing SK77824-1; CLIN 0024, Fin, Tail, Inert, 5 Inch/62 Caliber ERGM in accordance with Drawing SK77824-2; CLIN 0025, Retainer, Tail Fin, 5 Inch Inert ERGM in accordance with Drawing SK77825; CLIN 0026, 1 LOT, Data in accordance with CDRLS A001, A002, not separately priced. Note: the drawings in CLINS 0022-0025 are part of the weld assembly drawing in CLIN 0021. CLIN 0027, Obturator, Aft, ERGM Slug in accordance with Drawing 77799 Rev A; CLIN 0028, Obturator, Forward, ERGM Slug in accordance with Drawing 77800 Rev F; CLIN 0029, Shell, Fwd, 5-Inch Inert ERGM in accordance with Drawing SK77830 Rev E; CLIN 0030, Ramp, Obturator, 5-Inch Inert ERGM in accordance with Drawing SK77828 Rev B; CLIN 0031, Bulkhead, Inert, 5-Inch/62 Caliber ERGM in accordance with Drawing SK77829 Rev C; CLIN 0032, Body, Rocket Motor, 5-Inch Inert ERGM in accordance with Drawing SK77827 Rev B; CLIN 0033 Plate, Pusher, 5-Inch Inert ERGM in accordance with Drawing SK77826; CLIN 0034 Plate, Retainer, Fin, 5-Inch Inert ERGM in accordance with Drawing SK77837; CLIN 0035 Retainer, Fin, 5-Inch Inert ERGM in accordance with Drawing SK77838 Rev C; CLIN 0036, Pin, Crush, 5-Inch Inert ERGM in accordance with Drawing SK77839 Rev A; CLIN 0037, Detent, Fin, 5-Inch Inert ERGM in accordance with Drawing SK77840 Rev B; CLIN 0038, Screw, Fin Retainer, 5-Inch Inert ERGM in accordance with Drawing SK77841 Rev B; CLIN 0039, Aft Closure, 5-Inch Inert ERGM in accordance with Drawing SK77843 Rev D; CLIN 0040, Fin, Tail(Thick Section), 5-Inch Inert ERGM in accordance with Drawing SK77844 Rev E; CLIN 0041, Spring, Helical, Compression, 5-Inch Inert ERGM in accordance with Drawing SK77845 Rev B; CLIN 0042, Pin, Fin Pivot in accordance with Drawing SK77854; CLIN 0043, 1 LOT, Data in accordance with CDRLS A001, A002, not separately priced. Drawings stated above and CDRL requirements may be found by visiting the NSWCDD business opportunities website at http://www.nswc.navy.mil/supply. Items 0001 0013 shall be delivered F.O.B. Destination by 30 April 2001. Since historical information supports a 16 week lead time for delivery of quantities exceeding 50 EA, award of the contract is anticipated to be made no later than 7 January 2001. Option Items shall be delivered within 12 weeks after exercise of the option via modification to the contract. The Option Items are step ladder quantities which may be ordered in any combination by the government. Far 52.217-7, Option for Increased Quantity-Separately Priced Line Item is hereby incorporated by reference. The Contracting Officer will provide the contractor a thirty-day notice of intent before exercising an option. Option items, if exercised, will be completed no later than 30 Sept 2001. All CLINS are provided as individual components. Final assembly and painting will be performed by the Government. FAR 52.212-1, Instructions to Offerors Commercial Items applies to this solicitation and is hereby incorporated by reference. The Government will award a contract from this solicitation based on the following combination of factors: ability to deliver on time, price of items inclusive of Option Items, and past performance history for providing the same or similar items. Since the government may award any combination of option items, the Option Items will be evaluated for award purposes by averaging the unit price for each SUBCLIN. The total evaluated price for the Option Item will then be determined by multiplying the average unit price times the highest quantity set forth in the step-ladder. These Option Item totals will then be added to the total of the base items to establish the evaluated price. The maximum overall price established for the contract will be the sum of the base items and the results of the multiplication of the highest total quantity for each option item by the proposed unit price for that SUBCLIN. The offeror shall provide with its offer a list (at least three) of previous sales of the same or similar items with a description of the items, dollar value of contract, contract number, name or organization, points of contact technical and contracting, and telephone number(s). The offeror shall provide a technical explanation of how it intends to manufacture and deliver the items by the required delivery date. Offerors shall include a completed copy of the provisions at FAR 52.212-3 and DFAR 252.212-7000, Offeror Representations and Certifications Commercial Items. FAR 52.212-4, Contract Terms and Conditions Commercial Items applies to this acquisition and is hereby incorporated by reference. FAR 52.212-5, Contract Terms and Conditions Required to Implement Statutes or Executive Orders Commercial Items, subparagraphs (a), (b) 1, 5, 11, 12, 13, 14, 15, 20, 23, 27, (d), and (e) applies to this acquisition. DFARS 252.212-7001, Contract Terms and Conditions Required to Implement Statutes or Executive Orders Applicable to Defense Acquisitions of Commercial Items, subparagraphs (a) 252.225-7001, 252.225-7012, 252.243-7002, 252.247-7024, and (b) applies to this acquisition. The following additional DFARS provisions and/or clauses apply to this acquisition: 252.204-7004 Required Central Contractor Registration, offeror to include a completed copy of 252.225-7000 Buy American Act Balance of Payments Program Certificate, 252.225-7017 Prohibition on Award to Companies Owned by the Peoples Republic of China. This procurement is rated DO-A50. The closing date for receipt of proposals is 2 PM Eastern time on 4 December 2000. Proposals shall be delivered to Naval Surface Warfare Center, Dahlgren Division, Attn: SD11AorB/Bldg. 183, Room 102, 17320 Dahlgren Road, Dahlgren, VA 22448-5100, phone (540)653-7478/FAX (540)653-7088/Email sd11@nswc.navy.mil. In order to be eligible for award firms must be registered in the Central Contractor Registry (CCR). Offerors may obtain information on registration in the CCR by calling 1-888-227-2423, or via the Internet at http://www.ccr2000.com/. In order to confirm registration in the CCR, the offeror shall provide, clearly marked, its DUNS number and CAGE code that identifies the offerors name and address. The offeror shall provide an original and two copies of its firm-fixed price CLINS and SUBCLINS. The original shall be clearly marked original with original signature of person(s) authorized to bind the firm. The offeror shall provide an original and copy of its technical explanation of how it will manufacture and deliver on time from its price proposal along with sales history (list of previous sales for same or similar items) and past performance (including delivery) details which includes organization, point of contact and phone numbers for verification. A statement that the delivery will be met is not sufficient. See Note 1.
Web Link
NSWCDD Dahlgren Laboratory Procurement Division Web (http://www.nswc.navy.mil/supply)
Record
Loren Data Corp. 20001122/ASOL010.HTM (W-325 SN5070I2)

A - Research and Development Index  |  Issue Index |
Created on November 20, 2000 by Loren Data Corp. -- info@ld.com