59 -- ELECTRICAL AND ELECTRONIC EQUIPMENT COMPONENTS

Notice Date

September 28, 2000

Contracting Office

Bid Office, SPAWARSYSCEN, Code D21B, 53570 Silvergate Avenue, Bldg. A33, Room 0061, San Diego, CA 92152-5112

ZIP Code

92152-5112

Solicitation Number

N66001-00-Q-0408

Response Due

October 16, 2000

Point of Contact

Purchasing Agent: Claudine Huggins, Code D212, 619-553-3755/Contracting Officer: Sylvia Proffit, Code D211, 619-553-3292

Description

This is a combined synopsis/solicitation prepared in accordance with the format in the Federal Acquisition Regulation, supplemented with information included in this notice. This solicitation incorporates provisions and clauses at FAR 52.213-4 Terms and Conditions -- Simplified Acquisitions (Other Than Commercial Items) (FEB 1998), and any others that are applicable and in effect through the current Federal Acquisition Circular (FAC) and the Defense Acquisition Circular. It is the contractors responsibility to be familiar with all applicable clauses and provisions. No RFQ will be prepared or made available for distribution. While price will be a significant factor in the evaluation of offers, award will be based on responsive, responsible, technically acceptable offers received in response to this CBD advertisement.. Competitive awards may be based on the evaluation criteria stipulated in the Red, Yellow, Green (RYG) Contractor Evaluation System. The evaluation criteria is available upon request. Specifications are as follows: DFB LASER DIODE, CONTINUOUS WAVE (CW) WDM LASER FOR EXTERNAL MODULATION, 30mW OUTPUT POWER (1)1530.3NM WAVELENGTH, (2)1546.9nm WAVELENGTH, (3) 1552.5nm WAVELENGTH, QTY 1 EACH, DFB LASER DIODE, WDW LASER FOR DIRECT MODULATION, >2.5Gbs MODULATION BANDWIDTH, 20mW OUTPUT POWER (4) 1546.9nm, (5) 1552.5nm, DFB LASER DIODE WDM LASER FOR DIRECT MODULATION, >2.5Gbs MODULATION BANDWIDTH, 10mW OUTPUT, (6) 1540.55nm, (7) 1456.91nm, (8) 1553.32, (9) 1559.79nm, DFD LASER DIODE WITH INTEGRATED ELECTROABSORPTION MODULATION, >2.5Gbs MODULATION BANDWITDH, 1mW OUTPUT POWER. (10) 1546.9nm (11) 1552.5, Items (1-9) should have an identical pin-out from the 14pin butterfly package. Specification for Items 1-3 Items should be identical with the exception of the center wavelength DFB Laser diode continuous wave (CW) WDM laser for external modulation 30mW optical output power. Description: These items are packaged telecom grade distributed feedback (DFB) laser diodes with an optical fiber pigtail. The lasers are intended for use in continuous wave (CW) mode with an external modulator. The minimum peak optical power output required is 30mW. The device must be packaged in a 14pin butterfly package. The laser must have an internal integrated optical isolator. The optical fiber pigtail should be a polarization maintaining (PM) optical fiber connectorized with an FC/PC connector. The connector should be keyed to the slow axis of the PM fiber. The module must also have an integrated thermoelectric cooler (TEC) and thermistor as well an integrated photodiode for monitoring the laser power emission. Specifications: Item 1 Center Wavelength = 1530.3nm or 195.9THz, Item 2 Center Wavelength = 1546.9nm or 193.8THz, Item 3 Center Wavelength = 1552.5nm or 193.ITHz. The following applies to items 1-3: Minimum peak optical power output 30mW (15dBm), Threshold current maximum 40mA Laser forward current maximum 500mA, Deviation from expected center wavelength +/-0.1 nm Acceptable?temperature tuning range 15-35C, Spectral width (linewidth) maximum 5MHz, Side mode suppression ratio (SMSR), 35dB Relative intensity noise (RIN) maximum 100MHz to 2.5GHz -l40dB/Hz, TE/TM extinction ratio in optical fiber pigtail 20dBm minimum 20dB, TEC current maximum 1.3A, TEC voltage maximum 2.5 V, Thermistor resistance 9.5?10.5kohms, Case temperature operating range -10 to +60 C. Specification for Items 4-5 Items should be identical with the exception of the center wavelength DFB Laser diode >2.5Gbs modulation bandwidth WDM laser for direct modulation 20mW optical output power These items are packaged telecom grade distributed feedback (DFB) laser diodes with an optical fiber pigtail. The lasers are intended for direct modulation. The minimum optical power output required is 20mW. The device must be packaged in a 14pin butterfly package. The laser must have an internal integrated optical isolator. The optical fiber pigtail should be a single mode fiber (SMF?28 or equivalent) connectorized with an FC/PC connector. The module must also have an integrated thermoelectric cooler (TEC) and thermistor as well an integrated photodiode for monitoring the laser power emission. The DC bias input to the laser should have an RF filter on it. Specifications: Item 4 Center Wavelength = 1546.9nm or 193.8THz Item 5 Center Wavelength = 1552.5nm or 193.1THz The following applies to items 4?5: Minimum peak optical power output 20mW (13dBm) Modulation bandwidth minimum 2.5Gb/s Threshold current maximum 40mA Laser forward current maximum 200mA Deviation from expected center wavelength +/?0.Inm Acceptable temperature tuning range 15-35C Spectral width (linewidth) maximum 5MHz Side mode suppression ratio (SMSR) 35dB Relative intensity noise (RIN) maximum 100MHz to 2.5GHz -l30dB/Hz TEC current maximum 1.3A TEC voltage maximum 2.5V Thermistor resistance 9.5?10.5kohms Case temperature operating range -10 to +60 C Specification for Items 6-9 Items should be identical with the exception of the center wavelentgh DFB Laser diode WDM laser for direct modulation >2.5Gbs modulation bandwidth l0mW optical output power These items are packaged telecom grade distributed feedback (DFB) laser diodes with an optical fiber pigtail. The lasers are intended for direct modulation. The minimum optical power output required is IOmW. The device must be packaged in a 14pin butterfly package. The laser must have an internal integrated optical isolator. The optical fiber pigtail should be a single mode fiber (SMF?28 or equivalent) connectorized with an FC/PC connector. The module must also have an integrated thermoelectric cooler (TEC) and thermistor as well an integrated photodiode for monitoring the laser power emission. The DC bias input to the laser should have an RF filter on it. Item 6 Center Wavelength = 1540.55nm or 194.6THz Item 7 Center Wavelength = 1546.91nm or 193.8THz Item 8 Center Wavelength = 1553.32nm or 193.OTHz Item 9 Center Wavelength = 1559.79nm or 192.2THz The following applies to items 4?6.: Minimum peak optical power output IOmW (lOdBm) Modulation bandwidth minimum 2.5Gb/s Threshold current maximum 40mA Laser forward current maximum 200mA Deviation from expected center wavelength +/?0. 1 run Acceptable temperature tuning range 15?35C Spectral width (linewidth) maximum 5MHz Side mode suppression ratio (SMSR) 35dB Relative intensity?noise (RIN) maximum 100MHz to 2.5GHz -l30dB/Hz TEC current maximum 1.3A TEC voltage maximum 2.5V Thermistor resistance 9.5-10.5kohms Case temperature operating range -10 to +60 C Specification for Items 10-11 Items below should be identical with the exception of the center wavelentgh DFB Laser diode with integrated electroabsorption modulator >2.5Gbs modulation bandwidth 1mW optical output power These items are packaged telecom grade distributed feedback (DFB) laser diodes with a monolithically integrated electroabsorption modulator and an optical fiber pigtail. The lasers are modulated with the electroabsorption modulator. The minimum optical power output required is 1mW. The device must be packaged in a 14pin butterfly package. The laser must have an internal integrated optical isolator. The optical fiber pigtail should be a single mode fiber (SMF28 or equivalent) connectorized with an FC/PC connector. The module must also have an integrated thermoelectric cooler (TEC) and thermistor as well an integrated photodiode for monitoring the laser power emission. Item 10 Center Wavelength = 1546.9nm or 193.8THz Item 11 Center Wavelength = 1552.5nm or 193.1THz The following applies to items 10?11: Minimum peak optical power output ImW (OdBm) Modulation bandwidth minimum 2.5Gb/s Threshold current maximum 40mA Laser forward current maximum 200mA Deviation from expected center wavelength +/-0.lnm Acceptable temperature tuning range 15?35C Spectral width (linewidth) maximum 5MHz Side mode suppression ratio (SMSR) 35dB Relative intensity noise (RIN) maximum 100MHz to 2.5GHz -l30dB/Hz Modulator bias voltage minimum ?3V Modulator drive voltage maximum 3V Dynamic extinction ratio minimum l OdB TEC current maximum 1.3A TEC voltage maximum 2.5V Thermistor resistance 9.5?10.5kohms Case temperature operating range -10 to +60 C Interested parties are invited to respond to this synopsis. No RFQ is Available. Facsimile quotations are acdeptable and must be received on or before the COB on the closing date stated above. Facsimile quotations may be sent to (619)553-4842. Questions may be directed to the Purchasing Agent responsible for this action. The applicable Standard Industrial Code (SIC) and Size Standard is: 5065/100 employees

Record

Loren Data Corp. 20001002/59SOL006.HTM (W-272 SN502047)