General Services Administration, Federal Supply Service (FSS), Hardware and Appliance Center (6FE), 1500 East Bannister Road, Kansas City, MO, 64131

51 -- SPX CORP. TOOL KITS SOL SPX-TOOL-KITS-REQUEST-FOR-QUOTES-2-KITS DUE 081599 POC Ellie Upchurch, Contract, Phone (816) 926-7808, Fax (816) 926-7182, Email ellie.upchurch@gsa.gov -- Steve Mosby, Contract Specialist, Phone (816) 823-1294, Fax (816) 926-3678, Email steve.mosby@gsa.gov WEB: Visit this URL for the latest information about this, http://www.eps.gov/cgi-bin/WebObjects/EPS?ACode=P&;ProjID=SPX-TOOL-KITS -REQUEST-FOR-QUOTES-2-KITS&LocID=7. E-MAIL: Ellie Upchurch, ellie.upchurch@gsa.gov. ITEM NUMBER 1: 5180-01-333-1035 UI: KT TOOL KIT, GENERAL MECHANIC'S: 20 Kits The following header paragraph(s) shall apply to the item purchase description(s) where applicable. If there is a conflict between the item purchase description and the header paragraph(s), the header paragraph(s) shall take precedence over the item purchase description. Notwithstanding the requirements specified herein, cadmium plating is not acceptable. In the event no alternative coating, finish, or plating is specified, a rust preventative finish as used in standard commercial practice shall apply. Each set or kit shall contain a dated parts list or packing list citing the GSA contract number (if applicable), GSA purchase order number, date of purchase order, kit national stock number (NSN), each component NSN (if applicable), kit noun name, each component noun name, and quantity of each component. Unless otherwise specified in the item purchase description, each kit or set and each component of the kit or set shall have, in addition to any other required marking, identification marking indicating the manufacturer's name or identifying symbol, and the state or country of manufacture. The marking shall be engraved, etched, or stamped in such a manner that it will be permanent to the extent that it will remain clear and legible throughout the life of the item. Workmanship: Details of workmanship shall be in accordance with the best commercial standards and practices. Paints, coatings, platings, and finishes shall be smooth, adherent, continuous, and not stained or discolored. Fasteners shall be firmly secured and show no evidence of deformation, cross threading, or hazardous burrs. Adhesives and lubricants adequate for their intended purpose shall be properly and neatly applied. Adhesives shall be adequately cured. Wires and cables shall be neatly dressed and shall not be frayed or in contact with sharp edges. Wire and cable insulation shall show no evidence of burns, abrading, or pinch marks. There shall be no interference, binding, or galling of parts. External and bearing surfaces shall be free of tool and gouge marks, nicks, or other surface imperfections. The item shall be clean and free of corrosion and debris (e.g. chips shavings, slivers) or other foreign material. The item shall be free from manufacturing workmanship defects (e.g., loose, missing, binding or misaligned parts, sharp or rough external edges, corners or surfaces) and material defects (e.g., pits, rips, fins, burrs, tears, nodules, cracks, blisters) which may adversely impact the item's serviceability, durability, safety, or appearance. DESCRIPTION The kit shall be in accordance with U.S. Army Tank-Automotive Command part number 57K1182, parts list dated 21 April 97 to support the M915A2/M916A1 truck tractors or SPX part number J-43970 consisting of one each of the following 18 components: NOMENCLATURE VENDOR PART NUMBER Thermostat Seal Installer Kent Moore J8550 Handle, Installer Kent Moore J7079-2 Tester, Internal Kent Moore J38500-H Tester, Impeller Kent Moore J35687 Tool Kit, Internal Kent Moore J35888-60A Wiring Harness Kent Moore J 35751 ABS Cartridge Kent Moore J 38500-404 Wrench, Bearing Nut Oshkosh 409GX Socket, Wrench Snap-on Tools BWD482 Pliers, Slip Joint Snap-on Tools HCP48BP Indicator, Dial Starret 196A Swager, Hand U.S. Rigging P-21-005 Gaging Member, Plug Holland Hitch TF-0237 Tester, Kingpin, Lock Holland Hitch TF-TLN-1000 Adapter, Lock Test Holland Hitch TF-TLN-1500 ABS Test Adapter Kent Moore 446 300 3140 Tensionmeter, Dial Ind. Kent Moore BT-33-73F Leak Detector, Refrigerant Kent Moore 16500 End of Component List. PACKAGING Packaging in accordance with standard commercial practice. PACKING Packing in accordance with standard commercial practice. MARKING Marking in accordance with current version of Fed. Std. 123. ITEM NUMBER 2: 5180-01-333-1034 UI: KT TOOL KIT, GENERAL MECHANIC'S: 8 Kits The following header paragraph(s) shall apply to the item purchase description(s) where applicable. If there is a conflict between the item purchase descriptionand the header paragraph(s), the header paragraph(s) shall take precedence over the item purchase description. Notwithstanding the requirements specified herein, cadmium plating is not acceptable. In the event no alternative coating, finish, or plating is specified, a rust preventative finish as used in standard commercial practice shall apply. Each set or kit shall contain a dated parts list or packing list citing the GSA contract number (if applicable), GSA purchase order number, date of purchase order, kit national stock number (NSN), each component NSN (if applicable), kit noun name, each component noun name, and quantity of each component. Unless otherwise specified in the item purchase description, each kit or set and each component of the kit or set shall have, in addition to any other required marking, identification marking indicating the manufacturer's name or identifying symbol, and the state or country of manufacture. The marking shall be engraved, etched, or stamped in such a manner that it willbe permanent to the extent that it will remain clear and legible throughout the life of the item. Workmanship: Details of workmanship shall be in accordance with the best commercial standards and practices. Paints, coatings, platings, and finishes shall be smooth, adherent, continuous, and not stained or discolored. Fasteners shall be firmly secured and show no evidence of deformation, cross threading, or hazardous burrs. Adhesives and lubricants adequate for their intended purpose shall be properly and neatly applied. Adhesives shall be adequately cured. Wires and cables shall be neatly dressed and shall not be frayed or in contact with sharp edges. Wire and cable insulation shall show no evidence of burns, abrading, or pinch marks. There shall be no interference, binding, or galling of parts. External and bearing surfaces shall be free of tool and gouge marks, nicks, or other surface imperfections. The item shall be clean and free of corrosion and debris (e.g. chips shavings, slivers) or other foreign material. The item shall be free from manufacturing workmanship defects (e.g., loose, missing, binding or misaligned parts, sharp or rough external edges, corners or surfaces) and material defects (e.g., pits, rips, fins, burrs, tears, nodules, cracks, blisters) which may adversely impact the item's serviceability, durability, safety, or appearance. DESCRIPTION This kit shall be in accordance with U.S. Army Tank-Automotive Command part number 57K1183, parts list dated 20 April 94 to support the M915A2/M916A1 truck tractors or SPX Corp. part number J-43971, consisting of one each of the following 48 components: Tool components in SPX Corp. part number J43971 SPX DESCRIPTION PART NUMBER Installer J36326 Clamp, Material Lift J-35641-A Inserter and Remover J-25447-B Gage, Profile J-35637-A Driver, Bushing PT4365-1 Adjuster Lash, Cam J-35596 Inserter, Gear J-35949 Inserter, Seal J-35686-B Pin, Shoulder, Handle J-36235 Remover, Seal J-35993 Inserter and Remover J36310-A Puller, Drive Sprock J-26941 Piler, Retaining J-36347 Lifter, Rocker arm J-35996-A Guide Stud J-36107 Socket L-883 Barring Tool, Engine J-36237 Handle, Drive J-24202-4 Lifting, Bracket, Fly J-24365 Platte, retaining J-35652-B Inserter, Remover J-35988-B Pilot, Cam Gear J-35906 Socket, Socket Wrench J-36003-A Holding Bar Pinion J-3453 Inserter and remover 51100 Inserter and remover 302030 Bushing/bearing toolset 1764 Clamp 42052 Clamp plate, bushing 206459 Press adapter, bushing 206457 Removing adapter, bushing 302027 Inserter bearing 302026 Slider, spring compressor TFTLN-2500 Adjusting tool, worm J-37070 Wrench socket XE-16 Spanner attachment J-37464 Removing adapter, bushing 38095 Sling, engine and transmission J-36130-812 Spreader, sling 38841 Adapter, torque wrench 11663358-2 Checker, gear lash J-38662 Installation tool J-37073 Inserter, bearing J-37071 Inserter, bearing 204266 Tester, power steering J-26487-B Adapter kit, mechanical J-28593 Installer, output shaft J-24202-1A Shield, turbo protect J-26554-A Inserter, seal -- 3" cyl J-42381 End of Component List. PACKAGING Packaging in accordance with standard commercial practice. PACKING Packing in accordance with standard commercial practice. MARKING Marking in accordance with current version of Fed. Std. 123. Posted 08/09/99 (D-SN365050). (0221)

Loren Data Corp. http://www.ld.com (SYN# 0262 19990811\51-0001.SOL)