|
COMMERCE BUSINESS DAILY ISSUE OF JUNE 14,1999 PSA#2366U.S. Geological Survey, Branch Of Acquisition and Federal Assistance,
Box 25046, Denver Federal Center, Denver, CO 80225-0046 66 -- HIGH-QUALITY BROADBAND SEISMOMETERS DUE 072399 POC Marilyn
Hutchison, Purchasing Agent, (303) 236-5900, x327 or FAX (303) 236-2710
E-MAIL: USGS, CR, Acquisitions & Federal Assistance, mhutchi@usgs.gov.
Concerns having the ability to furnish the supplies described herein
are requested to give written notification (including the telephone
number for a point of contact) to the procuring office above within 45
calendar days from the date of this synopsis. The U.S. Geological
Survey, in order to extend the U.S. National Seismograph Network
(USNSN) and to provide enhanced seismic monitoring of the Nation, has
a requirement for two (2) high-quality broadband sensors for deployment
at remote field sites throughout the United States. Because the USNSN
project has strict performance criteria to insure the collection of
high-quality waveform data from seismic events, there are stringent
operational/performance requirements included in the following
specifications. New USNSN stations will have similar design
specifications to existing seismic stations within the USNSN, which
include high-fidelity digital acquisition systems, very broadband
seismometers, and real-time satellite communications. Data from these
stations will be integrated with real-time data from other USNSN
stations for global and national monitoring of earthquakes. Data from
these stations will also be transmitted to regional network centers in
the United States for local earthquake monitoring purposes. These
stations require installation of CMG-3NSN broadband seismometers
because they are the only commercially available sensor that meets the
USNSN specifications of being below the Low-Noise-Model (LNM) of the
Earth between 0.04 and 10 Hz and with a useable pass band between 0.005
Hz and 50 Hz (<LNM+10db). The CMG-3NSN sensor is completely
compatible with sensors at existing USNSN sites and with the USNSN data
loggers. The sensors must also met the following specifications: 1)
Flat to velocity between 0.04 and 50 Hz 2) Flat to acceleration between
0.005 and 0.033 Hz 3) Calibration enable (+5V) 4) Re-centering logic
mass position adjustment (+5V enable) 5) +20V differential signal out
6) 145 dB linear dynamic range in the pass band (10-0.03 Hz) 7)-105 dB
IHD 8) -60 dB cross axis coupling 9) cal resistor sufficient to
prevent clipping from a 5V input sourcing 10mA 10) below the Petterson
low-noise model in the frequency band 0.04-10 Hz 11) no more than 10dB
above the low noise model in the frequency band 0.005-50 Hz 12) USNSN
standard mil-style plastic 37-pin connectors Based on information
available at this time, and in accordance with 41 U.S.C. 253(c) (1),
implemented by FAR 5.302-1, the Government considers the item specified
as a sole source from Digital Technology Associates, Concord,
California, and proposes to negotiate a contract with that firm on that
basis. However, should additional sources be identified, they will be
considered. Firms who feel that they can furnish the required supplies
are invited to submit in writing an affirmative response to this
announcement, and such other materials which correspond to the required
items stated herein. This information will be evaluated and used to
determine if competitive opportunities exist. Since no solicitation
document exists, requests for such documents without accompanying
information will be considered non-responsive to this request without
further consideration. This notice may represent the Government's only
official notice of this procurement. See Note 22. Posted 06/08/99
(W-SN340728). (0159) Loren Data Corp. http://www.ld.com (SYN# 0353 19990614\66-0004.SOL)
66 - Instruments and Laboratory Equipment Index Page
|
|