Directorate Of Contracting, Oo-Alc 6050 Gum Lane/Bldg 1215, Hill Air Force Base, UT 84056-5825

13 -- G KIT SOL F42630-98-Q-66241 DUE 062698 POC For copy, PKX-2/Pamala Chaffee/(FAX)801-777-7522, For additional information contact Genee Ringel/Likm/[801]775-2093 Item 0001 NSN 1377-00-407-9651ES P/N: 7027302-10, Kit consists of a secondary control, control guillotine cart, a blade antenna guillotine cart, a leading edge antenna guillotine cart. 2 initiator fittings actuate the guillotine blades for severance of antenna leads. Secondsary control cables and an oxygen line. 7ea. Applicable to: F-111. Destn: FMS Countries. Delivery: 31 Dec 99 7 ea Item 0002 NSN 1377-00-407-9652ES D Kit P/N: 7027299-10, D kit contains a recovery parachutecatapult cartridge, a stabilization parachute catapult cartridge. These fire the stabilization chute cover and the recovery chute from the acft. F-111 crew module 7ea. Applicable to: F-111. Destn: FMS Countries. Delivery: 31 Dec 99 7 ea Item 0003 NSN 1377-00-408-7469ES Kit C P/N: 7027298-10, Kit C contains release retractor cartridges. These allow for the correct touch down altitude for the F-111 air crew module. 7ea. Applicable to: F-111 Acm. Destn: FMS Countries. Delivery: 31 Dec 99 7 ea Qualification requirements: Sources must bequalified prior to being considered for award. The solicitation will contain instructions for obtaining further information on this requirement. The requirements of FAR 9.202(A) have been completed and copies of the qualification requirements and standards may be obtained as described in the solicitation. These qualification requirements apply to line item(s) all All suppliers of this item must meet all requirments of drawing 7027302 cage 98747. The approximate issue/response date will be 08 Jun 98. The anticipated award date will be 26 Jun 98. Written procedure will be used for this solicitation. To: Oea Aerospace Inc, Fairfield Ca 94533-0659. To: Scot Inc, Downers Grove Il 60515-0705. No telephone requests. Only written or faxed requests received directly from the requestor are acceptable. All responsible sources solicited may submit a bid, proposal, or quotation which shall be considered. Award will be made only if the offeror, the product/service, or the manufacturer meets qualification requirements at the time of award in accordance with FAR clause 52.209-1. The solicitation identifies the office where additional information can be obtained concerning qualification requirements is cited in each individual solicitation. It is suggested that small business firms or others interested in subcontracting opportunities in connection with the described procurement make contact with the firm(s) listed. Request for copies of solicitations must reference the entire solicitation number, including purchasing office identification number. To expedite your request, limit the number of individual solicitation numbers requested per letter to not more than 10. Don't request information on this requirement until after the issue date. An Ombudsman has been appointed to hear concerns from offerors or potential offerors during the proposal development phase of this acquisition. The purpose of the Ombudsman is not to diminish the authority of the program director or contracting officer, but to communicate contractor, concerns, issues, disagreements, and recommendations to the appropriate government personnel. When requested, the Ombudsman will maintain strict confidentiality as to the source of the concern. The Ombudsman does not participate in the evaluation of proposals or in the source selection process. Interested parties are invited to call Brent W. Kendall if your concerns are not satisfied by the contracting officer (801)777-6991. ATTENTION: Contractor must be registered with Central Contractor Registration by 1 Jun 98 to be eligible for contact award or payment from any DOD activity. Information on registration and annual confirmation requirements may be obtained by calling 1-888-227-2423, or via the Internet at http://ccr.edi.disa.mil This part required engineering source approval by the design control activity in order to maintain the quality of the part. Existing unique design capability, engineering skills, and manufacturing knowledge by the qualified source(s) require acquisition of the part from the approved source(s). The approved source(s) retain data rights, manufacturing knowledge, or technical data that are not economically available to the Government, and the data or knowledge is essential to maintaining the quality of the part. An alternate source must qualify in accordance with the design control activity's procedures, as approved by the cognizant Government engineering activity. The qualification procedures must be approved by the Government engineering activity having jurisdiction over the part in the intended application. See Note (s) 26. (0139)

Loren Data Corp. http://www.ld.com (SYN# 0161 19980521\13-0001.SOL)