Corpus Christi Army Depot, Directorate of Contracting, 308 Crecy Street, Bldg 129, Stop 7, Corpus Christi, Texas 78419-5260

34 -- CNC MILLING MACHINE SOL DAAC83-97-T-0170 DUE 042297 POC Ozella Martinez, Contract Specialist, (512) 939-3133 or Brunetta D. Smith, Contracting Officer, (512) 939-2565 E-MAIL: BSmith@Corpus-Chr-EMH2.Army.Mil, POC e-mail address is OMartine@Corpus-Chr-EMH2.Army.Mil. This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in FAR Subpart 12.6, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation, written quotations are being requested and a written solicitation will not be issued. The solicitation is being issued as a Request for Quotation (RFQ), DAAC83-97-T-0170. The solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular (FAC) 90-42. This solicitation is under the Simplified Acquisition Procedures (SAP). Standard Industrial Classification is 3541 and the size standard is 500 employees. This will be a Firm-Fixed Price contract. The requirement consists of a 3-axis bed type CNC Milling Machine. Description (requirements) follows: Work Table: size: 10 inch x 54 inch; tee slots: 3 slots, 5/8 inch on 2 1/2 inch centers; table travel (x axis): 29 inches; saddle travel (y axis): 16 inches; head travel: 20 inches; quill travel: 5 inches; table load capacity: 1,300 lbs. Performance consists of the following: X and Y Travel: 190 inches per minute max; CNC Feed Rate: .01 to 100 inches per minute; Peak Torque: 165 inches/pound; Continuous Torque: 115 inches/pound; Spindle Speed: 500-5000 RPM (direct drive); 30 Taper Spindle Speed: 50-500 RPM (back gear); Inverter Drive Spindle Motor; Quill to Table Top Distance: 4-23 inches; Accuracy: 0.0004 inches for positioning and repeatability. Construction consists of the following: Precision Ground Ball Screws (X,Y,Z); hardened and ground way; spindle hardened and balanced; quill diameter 4 inch (class 7 precision bearings) and power drawbar. Power Specifications consist of: 3HP variable speed, spindle motor, AC; 3 phase, 220 VAC, 60 Hertz, 12 Amps (spindle motor); single phase, 220 VAC, 60 Hertz, 20 Amps (axis travel); single phase, 110 VAC, 60 Hertz, 5 Amps (controls). Control specifications consist of: CNC controls shall be by PC. The PC shall be a current model; 2MB RAM; 400 MB hard drive; 14 inch VGA monitor; 1.44 MB, 3 1/2 inch diskette; one RS-232 serial port; enhanced importer/exporter IGES compatible; manual and CNC automated operating modes and user friendly operating menus and conversational programming. Optional Features are: Fourth axis; Leveling Pads; Programmable Spindle Speed; Expanded Hard Drive Memory; Coolant Flood Control; Quartz Halogen; and CAT 30 Tooling Package. The CAT 30 Tooling Packare includes: 2 ea JT6 for drill chucks, Kennametal P/N QC30JT6197; 1 ea tool for face and shell mills, Kennametal P/N QC30SM75131; 1 ea tool for face and shell mills, Kennametal P/N QC30SM10031; 2 ea 3/8 inch end mill holder, Kennametal P/N QC30EM038175; 2 ea 1/2 inch end mill holder, Kennametal P/N QC30EM050175; 2 ea 5/8 inch end mill holder, Kennametal P/N QC30EM062175; 2 ea 3/4 inch end mill holder, Kennametal P/N QC30EM075213; 2 ea 7/8 inch end mill holder, Kennametal P/N QC30EM088250; 2 ea 1 inch end mill holder, Kennametal P/N QC30EM100269; 2 ea 3/16 inch end mill holder, Kennametal P/N QC30EM018175; 2 ea 1/4 inch end mill holder, Kennametal P/N QC30EM025175; 1 ea small collet holder, Kennametal P/N QC30TG075253; 1 ea large collect holder, Kennametal P/N QC30TG100394; 1 ea 4 inch ENCO vise/swivel base, ENCO P/N 425-7241 and 1 ea 6 inch ENCO vise/swivel base, ENCO P/N 425-7261. INSTALLATION: The contractor shall install the equipment at the consignee's facility within 20 days after delivery of the equipment. The contractor shall provide all labor and resources required for the installation except the activity will provide an electrician to connect electrical power in accordance with local regulations and laws. START-UP: The contractor shall validate the installation of the equipment by operating the equipment within 25 days of delivery. The contractor shall provide all labor and resources for the start-up operation. Operation of the equipment shall include modes for which the equipment is intended to perform. TRAINING: The contractor shall provide twenty (20) hourson-site operator and maintenance training for personnel at the Corpus Christi Army Depot after completion of installation and start-up of the equipment and within 30 days of delivery of the equipment. The contractor shall provide all resources and labor for this training. The training shall include operation and preventive maintenance evolutions on the equipment and shall be consistent with instructions in the contractor's Operation and Maintenance Manual. The contractor's instructor shall be expert in the operation and maintenance of the equipment and shall have a prepared training agenda. The contractor's Maintenance and Operations Manual shall be used as a training guide. Three copies of the Maintenance and Operations Manual are to be provided with the equipment. Delivery is to be made to the Corpus Christi Army Depot, FOB Destination, within 60 days after receipt of order. Quantity is one (1) each. The offeror must include with offer a list of references. Provision 52.212-1, Instructions to Offerors-Commercial Items applies to this acquisition. Contractor must include with offer a completed copy of the provision at 52.212-3, Offeror Representations and Certifications -- Commercial Items Clause 52.212-4, Contract Terms and Conditions- Commercial Items applies to this acquisition. FAR Clause 52.212-5, Contract Terms and Conditions Required to Implement Statutes or Executive Orders -- Commercial Items applies to this acquisition which indicates FAR Clauses 52.222-26, Equal Opportunity; 52.222-35, Affirmative Action for Special Disables and Vietnam Era Veterans; 52.222-36, Affirmative Action for Handicapped Workers; 52.222-37, Employment Reports on Special Disabled Veterans and Veterans of the Vietnam Era; and 52.225-3, Buy American Act -- Supplies. DFAR Clause 252.212-7001, Contract Terms and Conditions Required to Implement Statutes Or Executive Orders Applicable to Defense Acquisitions of Commercial Items applies to this acquisition which indicates DFAR Clause 252.225-7001, Buy American Act and Balance of Payment Program. FAR Clause 52.232-33, Mandatory Information for Electronic Funds Transfer Payment applies to this acquisition. Defense Priority Rating is DO. The quote is due to the Corpus Christi Army Depot Acquisition Office, Mail Stop 7, 308 Crecy Street, Corpus Christi, TX 78419-5260 by 5:00 p.m. 22 April 1997. Faxed quotes will be accepted. Fax number is 512-937-1126. POC is Ozella Martinez. All questions are to be submitted via FAX to above number. (0087)

Loren Data Corp. http://www.ld.com (SYN# 0205 19970401\34-0003.SOL)