Federal Aviation Administration, 601 E. 12th St., ACE-22.B, Kansas City, MO 64106

Y -- RELOCATION AND CONSTRUCTION OF RW 14R INSTRUMENT LANDING SYSTEM (ILS) COMPONENTS AND RW 32L LOCALIZER AND GLIDE SLOPE, EPPLEY AIRFIELD, OMAHA, NEBRASKA SOL DTFA09-96-B-26026 DUE 040196 POC Joseph A. York (816) 426-3106 Contracting Officer The intended scope of this project is to complete the Relocation and Installation of the Runway 14R ILS components along with the Runway 32L Localizer and Glide Slope. The project generally consists of, but is not limited to, the following: APPROACH LIGHTING SYSTEM WITH SEQUENCED FLASHERS (ALSF-2), RUNWAY 14R 1) Install Government Furnished engine generator, engine generator building, fuel tank and all pertinent accessories, plus all foundations. 2) Erect new ALSF Substation building along with foundations. 3) Install all frangible ALSF-2 Low Impact Resistant (LIR) light stations from station 1 + 00 to station 15 + 00 and install ALSF platforms from stations 16 + 00 through 24 + 00. 4) Install all power and control cable loops associated with ALSF from substation to light system as stated in the design package. 5) Install all necessary hardware and equipment as stated in the design package. 6) Install all cable runs as stated in design package for the threshold bar along with all necessary equipment, and etc. 7) Install and hook up all existing grounding and lightning protection as stated in design package. 8) Install and hook up all secondary power to ALSF substation as stated in design package. LOCALIZER, RUNWAY 32L 1) Install all anchor bolts as stated in design package for antenna system. 2) Relocate and install existing shelter on new foundations. 3) Install all necessary cables as stated in design package from localizer antenna pad to shelter. 4) Install and hook up all secondary power to shelter and to antenna pad. 5) Install and hook up all existing grounding and lightning protection as stated in design package. TOUCHDOWN RUNWAY VISUAL RANGE (RVR), RUNWAY 14R 1) Relocate and install transmissometer receiver and projector towers and equipment to new RVR plot. 2) Hook up all existing counterpoise cable to towers and equipment as stated in design package. 3) Install and hook up all necessary cables and appurtenances as stated in design package. 4) Install and hook up all secondary power to RVR system as stated in design package. GLIDE SLOPE (GS), RUNWAY 14R 1) Relocate and install glide slope antenna tower, bldg. & all necessary appurtenances as stated in design package at new plot. 2) Hook up and install all existing grounding and lightning protection system as stated in design package. 3) Install all necessary conduit runs and all necessary cables and all appurtenances as stated in design package. 4) Install and hook up all secondary power to GS shelter as stated in design package. INNER MARKER (IM) & FAR FIELD MONITOR (FFM), RUNWAY 14R 1) Install all cables to the inner marker and Far Field Monitor antenna foundations as stated in design package. 2) Hook up all existing grounding as stated in design package. MIDDLE MARKER (MM), RUNWAY 14R 1) Install new middle marker shelter and platform on existing foundations. 2) Install and hook up all cables and grounding as stated in design package. 3) Install and hook up all secondary power to MM shelter as stated in design package. 4) Install counterpoise on top of MM shelter as stated in design package. FIELD TERMINATION UNIT'S (FTU'S) 1) Install and hook up all control cables as stated in design package. 2) Install FTU along with foundation as stated in design package. 3) Install all conduits associated with control loop as stated in deisgn package. GLIDE SLOPE (GS), RUNWAY 32L 1) Remove the existing cap plates from the flanges and add a 10 ft. section of tower to the existing glide slope tower. 2) Extend the conduit and obstruction light to the top of the tower. 3) Extend the air terminal and air terminal ground wire. 4) Add coaxial cable ground box and connect to existing grounding system. 5) Remove existing coax cable conduit and weatherhead and install new conduit and weatherhead. Reroute new conduit through coaxial cable ground box. 6) Extend OSHA ladder and safety climbing device by 10 ft. 7) Repair hole in fiber glass shelter left from coaxial cable rerouting. The estimated price range of this project is $1,000,000 to $1,500,000. The SIC Code is 1629. This procurement is open to both large and small businesses. All responsible sources may submit an offer which will be considered. To obtain a copy of this solicitation you should submit your request, along with a certified check or money order in the the amount of $50.00 per set of the solicitation to the DOT/Federal Aviation Administration, ACE-22B, 601 E. 12th Street, Room 1524, Kansas City, Missouri 64106, Attn: Susan Chasteen. The certified check or money order should be made out to the Federal Aviation Administration. The charge for this solicitation is NON-REFUNDABLE. For questions about the availability of the solicitation documents, please contact Susan Chasteen at (816) 426-7312. This notice is for informational purposes for Minority, Women-Owned and Disadvantaged Business Enterprises: The Department of Transportation (DOT), Office of Small and Disadvantaged Business Utilization (OSDBU), has programs to assist minority, women-owned and disadvantaged business enterprises to acquire short-term working capital and bonding assistance for transportation-related contracts. This is applicable to any eligible prime or subcontract at any tier. The DOT Bonding Assistance Program enables firms to apply for bid, performance and payment bonds up to $1.0 million per contract. The DOT provides an 80% guaranty on the bond amount to surety against losses. Loans are also available under the DOT Short Term Lending Program (STLP) at prime interest rates to provide accounts receivable financing. The maximum line of credit is $500,000. For further information regarding the Bonding and Lending Programs, please call DOT of Small and Disadvantaged Business's Utilization at (800) 532-1169. For information concerning the acquisition, contact the contracting official listed above. (0012)

Loren Data Corp. http://www.ld.com (SYN# 0064 19960116\Y-0001.SOL)