Loren Data's SAM Daily™

SAMDAILY.US - ISSUE OF NOVEMBER 07, 2024 SAM #8381
SOLICITATION NOTICE

34 -- Bridgeport Milling Machine Overhaul

Notice Date

11/5/2024 5:47:39 AM
 

Notice Type

Combined Synopsis/Solicitation
 

NAICS

811310 — Commercial and Industrial Machinery and Equipment (except Automotive and Electronic) Repair and Maintenance
 

Contracting Office

FLEET READINESS CENTER PATUXENT RIVER MD 20670 USA
 

ZIP Code

20670
 

Solicitation Number

N6852025R0011
 

Response Due

11/8/2024 12:00:00 PM
 

Archive Date

11/23/2024
 

Point of Contact

Jenna Lang, Alex Julian
 

E-Mail Address

jenna.l.lang2.civ@us.navy.mil, alexander.m.julian2.mil@us.navy.mil
(jenna.l.lang2.civ@us.navy.mil, alexander.m.julian2.mil@us.navy.mil)
 

Small Business Set-Aside

SBA Total Small Business Set-Aside (FAR 19.5)
 

Description

Solicitation Information All quotes/responses shall be submitted via email to Jenna Lang at jenna.l.lang2.civ@us.navy.mil no later than 15:00PM Eastern Standard Time on 08 November 2024. N6852025R0011 is issued as a competitive procurement.� The Government intends to purchase on a firm fixed-price basis, and to solicit and negotiate the proposed purchase order on a competitive basis for the BRIDGEPORT MILLING MACHINE OVERHAUL listed under the authority implemented by Federal Acquisition Regulation (FAR) by FAR Part 12 and 13.��� Offeror�s must be registered in the System for Award Management Registration (SAM) database prior to submission of an offer to be considered for award of any DoD contract.� This may be accomplished electronically at http://www.sam.gov. This procurement is a total set-aside for small business under the authority of FAR Part 52.219-6.� ***Basis for Award*** Solicitation closing date/time is firm; proposals received after the deadline will not be accepted.� Your quote must contain enough technical information i.e. data sheet, drawing, specification, etc. for evaluation.� Your quote will only be evaluated based on the information provided.� The award will be made on the basis of lowest evaluated price of proposals meeting or exceeding the acceptability standards.� This is a firm fixed-price procurement; therefore, the initial offer should represent the vendor�s best quote in terms of price and technical acceptability.� A determination by the Government not to accept the proposal for not meeting the minimum requirement is solely within the discretion of the Government.� Interested parties must be registered in System for Award Management (SAM) Database prior to submission of an offer to be considered for award of any Department of Defense contract.� This can be accomplished electronically at http://www.sam.gov/vendor.cfm.� The Government will not pay for any information received. ***Instructions to offeror�s*** Please include the following information with your response: FOB: (Destination preferred) Shipping Cost if applicable (92135-7058):� Tax ID# Dun & Bradstreet # Cage Code: Small Business � Yes ___� No ___ Estimated Delivery Date: If available on a Pricelist please provide a copy. Total Amount: ______________________ Questions and Answers 1. Can you please elaborate on what ""core"" means in Section 3.2 of the SOW?� The Core is the original machine currently in the machine shop that will be taken away to be replaced with the new refurbished Bridgeport.� 2. Does the subject milling machine have a Accurite Millpower control installed already? Is a swap out of a equal machine acceptable?� The Accurite Mill Power control is not installed on the current machine. A swap out of an equal machine is acceptable.� 3. Section 3.1 includes the machine base/chassis in ""Minimum Machine Overhaul Requirements"", would the customer like a brand new base/chassis or a refurbishment�of the existing structure?� The basis/chassis can be used from a different/identical machine or refurbished from the original core�� 4. Will a forklift,�or any material moving equipment will be available on site?� Yes, we have material / moving equipment on site� 5. Is the�Mitutoyo Vertical Knee Power Kit�referring to the�Quill Kit?� Yes, the Mitutoyo Vertical Knee Power Kit refers to the quill kit. Part Number: 053906B � 6. Condition of current Bridgeport Milling Machine Series I in shop Worn bearings Some of the feeds are not working as well as they could The DRO (digital Readout) is not completely accurate Self-lubrication system is out of service. No real glaring issues that would make the machine completely un-usable
 

Web Link

SAM.gov Permalink
(https://sam.gov/opp/30ddcf9bd3ba4bf39f55cf4d46e40708/view)
 

Place of Performance

Address: San Diego, CA, USA

Country: USA
 

Record

SN07257424-F 20241107/241105230103 (samdaily.us)
 

Source

SAM.gov Link to This Notice
(may not be valid after Archive Date)

---

| FSG Index  |  This Issue's Index  |  Today's SAM Daily Index Page |