Loren Data's SAM Daily™

SAMDAILY.US - ISSUE OF SEPTEMBER 12, 2024 SAM #8325
SOLICITATION NOTICE

43 -- Urgent, Backup Air Compressor

Notice Date

9/10/2024 1:38:12 PM
 

Notice Type

Combined Synopsis/Solicitation
 

NAICS

333912 — Air and Gas Compressor Manufacturing
 

Contracting Office

NETWORK CONTRACT OFFICE 19 (36C259) Greenwood Village CO 80111 USA
 

ZIP Code

80111
 

Solicitation Number

36C25924Q0793
 

Response Due

9/11/2024 4:00:00 PM
 

Archive Date

11/10/2024
 

Point of Contact

Jonathan Saiz, Contracting Officer, Phone: 303-712-5775
 

E-Mail Address

jonathan.saiz@va.gov
(jonathan.saiz@va.gov)
 

Awardee

null
 

Description

Combined Synopsis/Solicitation Notice Combined Synopsis/Solicitation Notice Page 13 of 13 Request for Quote (RFQ): | Oil Free Rotary Air Compressor and Installation (Brand Name or Equal) Amendment 0001: The purpose of this amendment is to answer questions received in response to the solicitation and add two-line items to the price schedule below. Please ensure you are verifying the additions to the price schedule and quote accordingly. Answers. The contractor will need to provide and install a 175amp breaker to the panel. there is a 20-amp breaker for the air dryer. Locations for these disconnects are about 25 feet from compressor, and air dryer. Winterization will not be required. This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in FAR Subpart 12.6, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; quotes are being requested and a written solicitation will not be issued. The Government reserves the right to make no award from this solicitation. * The deadline for all questions is 3:00 pm MST, September 10, 2024 All questions must be submitted in writing no later than the question cut-off date marked above. All questions will be answered officially through an amendment to the solicitation. ** Quotes are to be provided to Jonathan.saiz@va.gov no later than 5:00pm MST, September 11, 2024. Quotes shall not be hand carried. Faxed quotes shall not be accepted. Emailed quotes are the only method of submitted quotes (4MB email limit). The Government reserves the right to make award solely on initial Quotes received. Offerors bear the burden of ensuring that all portions of the offer (and any authorized amendments) reach the designated office before the deadline specified in the solicitation. This RFQ shall be completed in its entirety, and signed and dated, failure shall not be considered for award. This is a Request for Quote (RFQ) and the solicitation number is 36C25924Q0793. The government anticipates awarding a firm-fixed price contract resulting from this solicitation. This solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular (FAC) 2024-04 effective May 01, 2024. The North American Industrial Classification System (NAICS) code for this procurement is 333912 with a small business size standard of 1,000 employees. This solicitation is not set aside and available for full and open competition. List of Line Items; This procurement is brand name or equal to the line items listed in the table. Line Item Description QTY UoM Unit Price Total Price 0001 Quincy Oil Free Rotary Air Compressor P/N: QOF-100V 1 EA 0002 Quincy Compressed Air Filter P/N: QWS 700 2 EA 0003 Quincy Compressed Air Dryer P/N: QBP-530 1 EA 0004 175 Amp Breaker 1 EA 0005 Installation of Air Compressor, Air Filer, and Air Dryer. 1 JB 0006 Installation of 175 Amp Breaker 1 JB 0005 Removal of Current Air Compressor, Air Filter, and Air Dryer. 1 JB Grand Total $ Description of Requirements for the items to be acquired: This is a Brand name or Equal solicitation, the salient characteristics required are found in the below statement of work. Quotes must match or exceed the salient characteristics to be considered for award.   FOB shall be destination. The cost of freight shall be included in the cost of the line items, rather than be a standalone line item. Cut sheets and Specification sheets proving the offered product meets all required specifications and salient characteristics shall be included with the quote. Quotes shall be accompanied by an authorized distributor letter provided by the manufacturer. The installation of the air compressor is time sensitive due to it replacing the back up that is inoperable. Should the main air compressor become inoperable the VAMC will lose HAVC, Dental and Pharmacy capabilities. This solicitation cannot be extended due to the time sensitive nature of this requirement. Please see the attached drawings, floor dimensions and pictures for reference. STATEMENT OF WORK Veteran Affairs Healthcare Systems (VA HCS) Replace BF118 Back-up Air Compressors at the Oklahoma VAMC, Oklahoma City, OK GENERAL: A. This project is to replace the inoperable BF118 backup air compressor with a new 100 HP air compressor, air dryer and 175-amp breaker located at the VAMC, OKC, Oklahoma. B. The contractor is fully responsible for verifying and validating all information contained within this statement of work. The contractor must fully evaluate the condition of the existing structures and verify the current condition of the project site. C. All measurements/quantities provided in this document are approximate and are to be used for reference only. The contractor will be responsible for taking on-site measurements and verifying all quantities and distances. D. All materials/fasteners/etc. must be new and provided by the contractor. E. The contractor shall abide by all Safety, Security, and Infection Control Policies and Procedures of the Oklahoma City VA Medical Center. F. VA facilities are tobacco-free. No smoking is permitted on VA property. The contractor is responsible for their subcontractor s compliance with this policy. G. All work must conform to, and comply with, the latest edition/version of ALL applicable VA, federal, state, and local laws, rules, regulations, codes, and standards. H. Expected performance period 100 days after the contract is awarded. Delivery and evaluation lead time will be heavily weighted. JUSTIFICATION: The existing Backup compressor in BF118 has met end-of-life. This compressor can t produce enough air pressure for the hospital s needs. STATEMENT OF WORK: The contractor shall provide supervision, manpower, and materials to replace the existing rotary screw air compressor that is oil-free type, Single-stage, oil-free, Air-cooled 100-hp rotary screw compressor. A crane will be required to remove and install equipment. A crane will be required to remove the current air compressor and install the new air compressor. The best place to put the road crane is 13th street which is 4 lanes, two lanes each way with a parking lane/shoulder. The entire west bound lane will not require complete closure, but it is possible to do so and it has been done before. The ambulance lane will not be blocked from entering the west side of the hospital. Ambulance services will be notified when roads are closed for installation of the air compressor. The cage where the air compressor will be dropped in and installed are as follows. Street to back of cage is 45 feet. Current inoperable air compressor to the back wall of the cage is 25 feet. Current inoperable compressor to the front of the cage is 25 feet. Please see attached pictures for reference of the cage housing the air compressor. Air Compressor 460 Volt, 3-Phase Air-cooled 125 Psig (+/-) Pressure Rotary Air Compressor Dim. of air outlet connection 2.5in Condensate connection is ½ in Compressed Air Filter 700 CFM @ 100 PSIG 2 inch NPT Connection Shall remove minimum 99% of bulk liquids Air Dryer Heated Blower Purge with mounted filters and 3-valve bypass and purge saving controller. 460Volt, 3-Phase 530 CFM @ 100 PSI 175 Amp Breaker Install new air compressor and dryer. Install 175-amp breaker. Remove and replace the existing air compressor and air dryer. IV. General 1. All electrical and piping needs to be included in quote. 2. Lockout tagout all electrical to air compressors. 3. The contractor shall obtain a permit for the crane. The crane will be used to rig out the old air compressors and install new air compressors. 4. Reconnect power to air compressors. 5. Start-up air compressor for operation testing, run air compressors at full load, and check operation. 6. Return to service. 7. Clean up of job site. V. Work Schedule Normal working hours are from 7:30 AM to 4:30 PM (local time) Monday through Friday except for weekends and established Federal Holidays. The following Federal legal holidays are observed by this facility: New Year s Day January 1 Martin Luther King s Birthday Third Monday in January President s Day Third Monday in February Memorial Day Last Monday in May Juneteenth June 19 Independence Day July 4 Labor Day First Monday in September Columbus Day Second Monday in October Veteran s Day November 11 Thanksgiving Day Fourth Thursday in November Christmas Day December 25 V. Parking and Security Badges 1. Contractor may park in Northwest parking area. Parking is limited. 2. There is a NO TOBACCO policy on premises 3. The contractor is responsible for getting Security Badges for anyone who will be at the facility. The COR will help with getting badges. Delivery and acceptance is to be F.O.B Destination (FAR 52.247-34) at the Veterans Affairs Medical Center, located at: Oklahoma City VAMC 921 NE 13th Street Oklahoma City, OK. 73104 United States 52.212-1, Instructions to Offerors--Commercial Items applies to this acquisition ADDENDUM to FAR 52.212-1 INSTRUCTIONS TO OFFERORS COMMERCIAL Gray market items are Original Equipment Manufacturer s (OEM) goods sold through unauthorized channels in direct competition with authorized distributors. This procurement is for new OEM medical supplies, medical equipment and/or services contracts for maintenance of medical equipment (i.e. replacement parts) for VA Medical Centers.  No remanufactures or gray market items will be acceptable. Offeror shall be an OEM, authorized dealer, authorized distributor or authorized reseller for the proposed medical supplies, medical equipment and/or services contracts for maintenance of medical equipment (i.e. replacement parts), verified by an authorization letter or other documents from the OEM, such that the OEM s warranty and service are provided and maintained by the OEM.  All software licensing, warranty and service associated with the medical supplies, medical equipment and/or services contracts for maintenance of medical equipment shall be in accordance with the OEM terms and conditions. The delivery of gray market items to the VA in the fulfillment of an order/award constitutes a breach of contract.  Accordingly, the VA reserves the right enforce any of its contractual remedies. This includes termination of the contract or, solely at the VA s election, allowing the Vendor to replace, at no cost to the Government, any remanufactured or gray market item(s) delivered to a VA medical facility upon discovery of such items. Offerors providing an or equal product(s) must adhere to the terms in FAR 52.211-6. If an item in this solicitation is identified as brand name or equal, the purchase description reflects the characteristics and level of quality that will satisfy the Government s needs. The salient physical, functional, or performance characteristics that equal products must meet or exceed are specified in the solicitation. To be considered for award, offers of equal products, including equal products of the brand name manufacturer, must Meet the salient physical, functional, or performance characteristic specified in this solicitation; Clearly identify the item by- Brand name, if any and Make or model number, Include descriptive literature such as illustrations, drawings, or a clear reference to previously furnished descriptive data or information available to the Contracting Officer; and Clearly describe any modification the offeror plans to make in a product to make it conform to the solicitation requirements. Mark any descriptive material to clearly show the modification. The contracting officer will evaluate equal products on the basis of information furnished by the offeror or identified in the offer and reasonably available to the contracting officer. The Contracting Officer is not responsible for locating or obtaining any information not identified in the offer. Unless the offeror clearly indicates in its offer that the product being offered is an equal product, the offeror shall provide the brand name product referenced in the solicitation. Any award made as a result of this solicitation will be made on an All or Nothing Basis. State if quoted items are available and priced through offerors existing Government-wide Acquisition Contract (GWAC), GSA Multiple Award Schedule (MAS) contract, or VA-wide Acquisition Contract. Offerors are warned against contacting any VA personnel other than the Contracting Officer and Contract Specialist prior to placement of any award made resulting from this RFQ. If such contact occurs and found to be prejudicial to competing contactors, the offeror making such contact may be excluded from award considerations. All proprietary information shall be clearly and properly marked. If the Offeror submits annexes, documentation, attachments or the like, not specifically required by this solicitation, such will count against the Offeror s page limitations unless otherwise indicated in the specific volume instructions below. All information shall be confined to the appropriate file. The offeror shall confine submissions to essential matters, sufficient to define the quote and provide an adequate basis for evaluation. Offerors are responsible for including sufficient details, in a concise manner, to permit a complete and accurate evaluation of each quote. Submission of quote shall include the following volumes: (I) - Technical capability or quality of the item offered to meet the Government requirement; (II) Price; Volume (III) Delivery and Installation Lead Time. Volume I - Technical capability or quality of the item offered to meet the Government requirement The offeror shall submit specifications, cut sheets, or brochures confirming the equal products, including equal products of the brand name manufacturer submitted, meets or exceeds the salient physical, functional, or performance characteristic specified in this solicitation. The product(s) quoted must be identified by brand name, if any, and make or model number. Volume II Price Price - The offeror shall complete the pricing schedule provided in Section (v) above: Price/Cost Schedule. Volume III Delivery and Installation Lead Time Offers quote shall provide the delivery lead time and when the installation is expected to be completed. (End of Addendum to 52.212-1) 52.212-2, Evaluation--Commercial Items applies to this acquisition ADDENDUM to FAR 52.212-2 EVALUATION COMMERCIAL ITEMS: The Government will award a contract resulting from this solicitation to the responsible offeror whose offer conforming to the solicitation will be most advantageous to the Government considering price and other factors. The following factors shall be used to evaluate quotations: Factor 1. Technical capability or quality of the item offered to meet the Government requirement Factor 2. Price Factor 3. Delivery and installation lead time Evaluation Approach. The Government will evaluate quotations using the comparative evaluation process outlined in FAR 13.106-2(b)(3), where quotations will be compared to one another to determine which provides the best benefit to the Government. The Government reserves the right to consider a quotation other than the lowest price that provides additional benefit(s). Quotations may exceed minimum requirements of the solicitation. The Government reserves the right to select a quotation that provides benefit to the Government that exceeds the minimum requirements of the solicitation but is not required to do so. Each response must meet the minimum requirements of the solicitation. The Government is not requesting or accepting alternate quotations. The evaluation will consider the following: Factor 1. Technical capability or quality of the item offered to meet the Government requirement: The quotation will be evaluated to the extent to which it can meet and/or exceed the Government s requirements as outlined in the solicitation and based on the information requested in the instructions to quoters section of the solicitation. Factor 2. Price: The Government will evaluate the price by adding the total of all line item prices. The Government may use various price analysis techniques and procedures to make a price reasonableness determination. Offers that do not meet or exceed the technical capability or quality of the item offered to the Government requirement shall not be selected regardless of price. Factor 3. Delivery and installation lead time: The government will evaluate the offerors lead time for delivery and installation, which may be deemed of more importance than price. (End of Addendum to 52.212-2) 52.212-3, Offeror Representations and Certifications Commercial Items, applies to this acquisition. Offerors must complete annual representations and certifications electronically via the System for Award Management (SAM) website located at https://www.sam.gov/portal in accordance with FAR 52.212-3, Offerors Representations and Certifications Commercial Items. If paragraph (j) of the provision is applicable, a written submission is required. Offerors must be registered in SAM at time of offer submission. 52.212-4, Contract Terms and Conditions--Commercial Items applies to this acquisition 52.212-5, Contract Terms and Conditions Required to Implement Statutes or Executive Orders--Commercial Items (JUL 2020) applies to this acquisition FAR 52.212-5 applies to this acquisition with the following FAR clauses incorporated by reference; FAR 52.204-10 Reporting Executive Compensation & First-Tier Subcontract Awards (JUN 2020) FAR 52.204-16 Commercial and Government Entity Code Reporting (AUG 2020) FAR 52.204-24 Representation Regarding Certain Telecommunications and Video Surveillance Services or Equipment (OCT 2020) FAR 52.209-6 Protecting the Government s Interest When Subcontracting with Contractors Debarred, Suspended, or Proposed for Debarment (JUN 2020) FAR 52.222-3 Convict Labor (JUN 2003) FAR 52.222-19 Child Labor Cooperation with Authorities and Remedies (JUL 2020) FAR 52.222-21 Prohibition of Segregated Facilities (APR 2015) FAR 52.222-26 Equal Opportunity (SEP 2016) FAR 52.222-35 Equal Opportunity for Veterans (JUN 2020) FAR 52.222-36 Equal Opportunity for Workers with Disabilities (JUN 2020) FAR 52.222-37 Employment Reports on Veterans (JUN 2020) FAR 52.222-40 Notification of Employee Rights Under the National Labor Relations Act (DEC 2010) FAR 52.222-50 Combating Trafficking in Persons (OCT 2020) FAR 52.223-18 Encouraging Contractor Policies to Ban Text Messaging While Driving (JUN 2020) FAR 52.225-1 Buy American Supplies (JAN 2021) FAR 52.225-13 Restrictions on Certain Foreign Purchases (JUN 2008) FAR 52.232-33 Payment by Electronic Funds Transfer System for Award Management (Oct 2018) Additional contract requirements or terms and conditions: 52.217-6 Option for Increased Quantity. The Government may increase the quantity of supplies called for in the Schedule at the unit price specified. The Contracting Officer may exercise the option by written notice to the Contractor within eight weeks. Delivery of the added items shall continue at the same rate as the like items called for under the contract, unless the parties otherwise agree. 52.225-5 Trade Agreements. As prescribed in 25.1101(c)(1), insert the following clause: Trade Agreements (Nov 2023) (a) Definitions. As used in this clause- Caribbean Basin country end product (1) Means an article that- (i) (A) Is wholly the growth, product, or manufacture of a Caribbean Basin country; or (B) In the case of an article that consists in whole or in part of materials from another country, has been substantially transformed in a Caribbean Basin country into a new and different article of commerce with a name, character, or use distinct from that of the article or articles from which it was transformed; and (ii) Is not excluded from duty-free treatment for Caribbean countries under 19 U.S.C.2703(b). (A) For this reason, the following articles are not Caribbean Basin country end products: (1) Tuna, prepared or preserved in any manner in airtight containers; (2) Petroleum, or any product derived from petroleum; (3) Watches and watch parts (including cases, bracelets, and straps) of whatever type including, but not limited to, mechanical, quartz digital, or quartz analog, if such watches or watch parts contain any material that is the product of any country to which the Harmonized Tariff Schedule of the United States (HTSUS) column2 rates of duty apply (i.e., Afghanistan, Cuba, Laos, North Korea, and Vietnam); and (4) Certain of the following: textiles and apparel articles; footwear, handbags, luggage, flat goods, work gloves, and leather wearing apparel; or handloomed, handmade, and folklore articles; (B) Access to the HTSUS to determine duty-free status of articles of these types is available at https://usitc.gov/tata/hts/index.htm. In particular, see the following: (1) General Note3(c), Products Eligible for Special Tariff treatment. (2) General Note17, Products of Countries Designated as Beneficiary Countries under the United States-Caribbean Basin Trade Partnership Act of 2000. (3) Section XXII, Chapter 98, Subchapter II, Articles Exported and Returned, Advanced or Improved Abroad, U.S. Note7(b). (4) Section XXII, Chapter 98, Subchapter XX, Goods Eligible for Special Tariff Benefits under the United States-Caribbean Basin Trade Partnership Act; and (2) Refers to a product offered for purchase under a supply contract, but for purposes of calculating the value of the acquisition, includes services (except transportation services) incidental to the article, provided that the value of those incidental services does not exceed that of the article itself. Designated country means any of the following countries: (1) A World Trade Organization Government Procurement Agreement (WTO GPA) country (Armenia, Aruba, Australia, Austria, Belgium, Bulgaria, Canada, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hong Kong, Hungary, Iceland, Ireland, Israel, Italy, Japan, Korea (Republic of), Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Moldova, Montenegro, Netherlands, New Zealand, North Macedonia, Norway, Poland, Portugal, Romania, Singapore, Slovak Republic, Slovenia, Spain, Sweden, Switzerland, Taiwan (known in the World Trade Organization as ""the Separate Customs Territory of Taiwan, Penghu, Kinmen and Matsu (Chinese Taipei)""), Ukraine, or United Kingdom); (2) A Free Trade Agreement (FTA) country (Australia, Bahrain, Chile, Colombia, Costa Rica, Dominican Republic, El Salvador, Guatemala, Honduras, Korea (Republic of), Mexico, Morocco, Nicaragua, Oman, Panama, Peru, or Singapore); (3) A least developed country (Afghanistan, Angola, Bangladesh, Benin, Bhutan, Burkina Faso, Burundi, Cambodia, Central African Republic, Chad, Comoros, Democratic Republic of Congo, Djibouti, Equatorial Guinea, Eritrea, Ethiopia, Gambia, Guinea, Guinea-Bissau, Haiti, Kiribati, Laos, Lesotho, Liberia, Madagascar, Malawi, Mali, Mauritania, Mozambique, Nepal, Niger, Rwanda, Samoa, Sao Tome and Principe, Senegal, Sierra Leone, Solomon Islands, Somalia, South Sudan, Tanzania, Timor-Leste, Togo, Tuvalu, Uganda, Vanuatu, Yemen, or Zambia); or (4) A Caribbean Basin country (Antigua and Barbuda, Aruba, Bahamas, Barbados, Belize, Bonaire, British Virgin Islands, Curacao, Dominica, Grenada, Guyana, Haiti, Jamaica, Montserrat, Saba, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Sint Eustatius, Sint Maarten, or Trinidad and Tobago). Designated country end product means a WTO GPA country end product, an FTA country end product, a least developed country end product, or a Caribbean Basin country end product. End product means those articles, materials, and supplies to be acquired under the contract for public use. Free Trade Agreement country end product means an article that- (1) Is wholly the growth, product, or manufacture of a Free Trade Agreement (FTA) country; or (2) In the case of an article that consists in whole or in part of materials from another country, has been substantially transformed in an FTA country into a new and different article of commerce with a name, character, or use distinct from that of the article or articles from which it was transformed. The term refers to a product offered for purchase under a supply contract, but for purposes of calculating the value of the end product includes services (except transportation services) incidental to the article, provided that the value of those incidental services does not exceed that of the article itself. Least developed country end product means an article that- (1) Is wholly the growth, product, or manufacture of a least developed country; or (2) In the case of an article that consists in whole or in part of materials from another country, has been substantially transformed in a least developed country into a new and different article of commerce with a name, character, or use distinct from that of the article or articles from which it was transformed. The term refers to a product offered for purchase under a supply contract, but for purposes of calculating the value of the end product, includes services (except transportation services) incidental to the article, provided that the value of those incidental services does not exceed that of the article itself. United States means the 50 States, the District of Columbia, and outlying areas. U.S.-made end product means an article that is mined, produced, or manufactured in the United States or that is substantially transformed in the United States into a new and different article of commerce with a name, character, or use distinct from that of the article or articles from which it was transformed. WTO GPA country end product means an article that- (1) Is wholly the growth, product, or manufacture of a WTO GPA country; or (2) In the case of an article that consists in whole or in part of materials from another country, has been substantially transformed in a WTO GPA country into a new and different article of commerce with a name, character, or use distinct from that of the article or articles from which it was transformed. The term refers to a product offered for purchase under a supply contract, but for purposes of calculating the value of the end product includes services, (except transportation services) incidental to the article, provided that the value of those incidental services does not exceed that of the article itself. (b) Delivery of end products. The Contracting Officer has determined that the WTO GPA and FTAs apply to this acquisition. Unless otherwise specified, these trade agreements apply to all items in the Schedule. The Contractor shall deliver under this contract only U.S.-made or designated country end products except to the extent that, in its offer, it specified delivery of other end products in the provision entitled ""Trade Agreements Certificate."" (End of clause) 52.225-6 Trade Agreements Certificate. As prescribed in 25.1101(c)(2), insert the following provision: Trade Agreements Certificate (Feb 2021) (a) The offeror certifies that each end product, except those listed in paragraph (b) of this provision, is a U.S.-made or designated country end product, as defined in the clause of this solicitation entitled ""Trade Agreements."" (b) The offeror shall list as other end products those supplies that are not U.S.-made or designated country end products. Other End Products: Line Item No. Country of Origin ______________ _________________ ______________ _________________ ______________ _________________ [List as necessary] (c) The Government will evaluate offers in accordance with the policies and procedures of part 25 of the Federal Acquisition Regulation. For line items covered by the WTO GPA, the Government will evaluate offers of U.S.-made or designated country end products without regard to the restrictions of the Buy American statute. The Government will consider for award only offers of U.S.-made or designated country end products unless the Contracting Officer determines that there are no offers for such products or that the offers for those products are insufficient to fulfill the requirements of this solicitation. (End of provision) 852.212-70, Provisions and Clauses Applicable to VA Acquisition of Commercial Items (Apr 2020) VAAR 852.203-70 Commercial Advertising (MAY 2018) VAAR 852.232-72 Electronic Submission of Payment Requests (NOV 2018) VAAR 852.233-70 Protest Content/Alternative Dispute Resolution (SEP 2018) VAAR 852.233-71 Alternate Protest Procedure (SEP 2018) VAAR 852.246-71 Rejected Goods (OCT 2018) 852.252-70, Solicitation Provisions or Clauses Incorporated by Reference (Jan 2008) The following provisions or clauses incorporated by reference in this solicitation must be completed by the offeror or prospective contractor and submitted with the quotation or offer. Copies of these provisions or clauses are available on the Internet at the web sites provided in the provision at FAR 52.252-1, Solicitation Provisions Incorporated by Reference, or the clause at FAR 52.252-2, Clauses Incorporated by Reference. Copies may also be obtained from the contracting officer. https://www.acquisition.gov/vaar The following FAR provisions are to be incorporated by reference: FAR 52.204-7 System for Award Management (OCT 2018) FAR 52.204-16 Commercial and Government Entity Code Reporting (AUG 2020) FAR 52.229-11 Tax on Certain Foreign Procurements Notice and Representation (JUN 2020) The following VAAR provisions are to be incorporated by reference: None The following FAR clauses are incorporated by reference: FAR 52.203-17 Contractor Employee Whistleblower Rights and Requirement to Inform Employees of Whistleblower Rights (JUN 2020) FAR 52.204-13 System for Award Management Maintenance (OCT 2018) FAR 52.204-18 Commercial and Government Entity Code Maintenance (AUG 2020) FAR 52.232-40 Providing Accelerated Paymentsto Small Business Subcontractors (NOV 2021) The following VAAR clauses are to be incorporated by reference: VAAR 852.212-71 Gray Market Items (APR 2020) The Defense Priorities and Allocations System (DPAS) does not apply. Offers are due to jonathan.saiz@va.gov no later than 5:00pm MST, September 11, 2024. Name and email of the individual to contact for information regarding the solicitation: Jonathan Saiz Jonathan.saiz@va.gov
 

Web Link

SAM.gov Permalink
(https://sam.gov/opp/5360418060dc47768fce4144074bc786/view)
 

Place of Performance

Address: OKC VAMC 921 NE 13th Street Oklahoma City OK, 73104
 

Record

SN07205577-F 20240912/240910230122 (samdaily.us)
 

Source

SAM.gov Link to This Notice
(may not be valid after Archive Date)

---

| FSG Index  |  This Issue's Index  |  Today's SAM Daily Index Page |