SOLICITATION NOTICE
J -- NCTC Port Hueneme Steel Shop Preventative Maintenance
- Notice Date
- 6/10/2023 12:24:41 AM
- Notice Type
- Presolicitation
- NAICS
- 811310
— Commercial and Industrial Machinery and Equipment (except Automotive and Electronic) Repair and Maintenance
- Contracting Office
- NAVSUP FLT LOG CTR SAN DIEGO SAN DIEGO CA 92136 USA
- ZIP Code
- 92136
- Solicitation Number
- N0024423R0057
- Response Due
- 6/12/2023 9:00:00 AM
- Archive Date
- 06/27/2023
- Point of Contact
- Nelson J. Arias, Phone: 6195569532
- E-Mail Address
-
nelson.j.arias.civ@us.navy.mil
(nelson.j.arias.civ@us.navy.mil)
- Small Business Set-Aside
- SBA Total Small Business Set-Aside (FAR 19.5)
- Description
- This is a pre-solicitation notice for NAVSUP Fleet Logistics Center (FLC) San Diego. This acquisition is for quarterly and annual preventative maintenance on steelshop equipment for Naval Construction Training Center (NCTC) on Naval Base Ventura County (NBVC). Work shall include: Quarterly Maintenance of the following equipment; Jet Zip Miter Bandsaw, model J-9225 Pexto Shear, model 152K Jet Mill, model JMD-18PFN LeBlonde Regal Lathe, model 13x42 Piranha Ironworker, model P-50 Jet Horizontal Band saw, model MDS-132EVS-H Ingersoll Rand Compressor, model RS37I-A125 Piranha CNC Hydraulic Guillotine Shear, model ��-10� ELE International Concrete Cylinder Splitter, model 36-0740/02 Each quarterly inspection shall include: Inspection of electrical controls, cabling, wiring and all switches Inspection of motor amps and noise Drive belts and pulley�s Coolant pumps, hydraulic cylinders and cylinder rods Check and adjust as necessary gibs and drive nuts for X and Y axis where applicable Check oil levels and top off as needed Inspection of hydraulic hoses and valves for damage or leaks Inspection of lubrication systems, lube lines and lube to all points Check gearbox and gears for noise where applicable Check Spindle down drive and spindle run out where applicable and adjust Check and adjust gibs and blade gaps where necessary Check mechanical linkage and clamp locks where applicable Check notcher blades, shear blades where applicable and check for sharpness Annual Preventive maintenance to include in addition to quarterly requirements above; Removal of used oil, cleaning of oil tanks where applicable. Check for loose hardware and tighten to manufacture spec as necessary. Installation of filters and oil as applicable. The procurement is set-aside for Small Businesses only. The NAICS code for this procurement is 811310 (Commercial and Industrial Machinery and Equipment) with a size standard of $12.5 million. The due date for receipt of proposals will be stated in the solicitation. There will be an electronic submission with which the solicitation will explain in further detail. The solicitation will be available for download through SAM.gov. The solicitation will be posted on or about June 12, 2023 and should be downloaded from this website at that time.� All questions and bids must be submitted via email to nelson.j.arias.civ@us.navy.mil. Questions received via phone will not be acknowledged. Electronic copies of all volumes will be required to be received by the Contracting Office provided in the RFP by the closing date and time specified in order to be considered for award.
- Web Link
-
SAM.gov Permalink
(https://sam.gov/opp/c3233f6117e445da8985b8ecad117abb/view)
- Place of Performance
- Address: Port Hueneme, CA, USA
- Country: USA
- Country: USA
- Record
- SN06711457-F 20230612/230610230102 (samdaily.us)
- Source
-
SAM.gov Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's SAM Daily Index Page |