SAMDaily.us | PRESOL | J | Gage Block Calibration

SAMDAILY.US - ISSUE OF FEBRUARY 17, 2023 SAM #7752
SOLICITATION NOTICE

J -- Gage Block Calibration

Notice Date: 2/15/2023 1:09:34 PM
Notice Type: Combined Synopsis/Solicitation
NAICS: 811210 —
Contracting Office: NORFOLK NAVAL SHIPYARD GF PORTSMOUTH VA 23709-1001 USA
ZIP Code: 23709-1001
Solicitation Number: N4215823QN026
Response Due: 2/17/2023 12:00:00 PM
Archive Date: 02/18/2023
Point of Contact: Christopher Vieira, Phone: 7573968356
E-Mail Address: christopher.f.vieira.civ@us.navy.mil
(christopher.f.vieira.civ@us.navy.mil)
Description: REQUEST FOR QUOTE: Issued To:�� Starret Webber Vendors Solicitation Number:�� N4215823QN026 Solicitation Issue Date:�� Wednesday, February 15 2023 Response Deadline:�� Friday, February 17 2023 prior to 1500 (EST) POC: Christopher Vieira �Christopher.f.vieira.civ@us.navy.mil 757-396-8356 �� GENERAL INFORMATION This is a Request for Quotation (RFQ) This acquisition is for Authorized Starret Webber Vendors. North American Industry Classification System Code (NAICS) 811210 � Repairing and Maintaining Consumer Electronics and Product or Service Code (PSC) J066 - Maint/Repair/Rebuild Of Equipment- Instruments And Laboratory Equipment.. The size standard is $30M. The Government intends to award one Firm Fixed Price, (FFP) contract to Starret Webber and no quotes from other sources will be considered. �This is a Single Source acquisition based on FAR 13.106-1(b)(1) as only one source, Starrett Webber is authorized to perform and they will provide an authorized vendor has the proprietary knowledge to execute the Government requirement. REQUIREMENT INFORMATION Description: The Norfolk Naval Shipyard, (NNSY) has a requirement for the calibration of Gage Blocks in accordance with, (IAW) Attachment 1 � Statement of Work. Place of Performance � (FOB): Origin, (to be proposed by vendor within range listed in SOW) Line Item� � � � � � � Description� � � � � � � � � � � �Quantity� � � � � � � � � � � �Unit of Measure 0001� � � � � � � � Gage Block Calibration� � � � � � � � �1� � � � � � � � � � � � � � � � � � � � � �Lot INSTRUCTIONS TO OFFEROR Questions may be submitted to the POC listed above no later than 1500 (EST) on February 16, 2023 or they may not be answered. Quotes in response to this solicitation must be submitted via email to the POC listed above no later than the established deadline. Quotes must be valid through March 31 2023. EVALUATION CRITERIA The Government intends to award one Firm Fixed Price, (FFP) contract resulting from this solicitation to the responsible offeror whose quote conforms to the solicitation will be most advantageous to the Government, price and other factors considered. This solicitation will be evaluated with Lowest Price Technically Acceptable, (LPTA) criteria. The ��following factors shall be used to evaluate offers: Ability to Receive Award, if a contractor has been disbarred, has any active exclusions listed in SAM.gov or an Inactive SAM.gov account at the time their quote was submitted, they are not eligible for award. If the vendor does not meet the Set-Aside criteria, (if any) listed in paragraph 4 and 5 of the GENERAL INFORMATION Section, they cannot be eligible for award. Technical Acceptability, technical evaluation team will evaluate by assigning a rating of �acceptable� or �unacceptable�. The Government will evaluate the lowest priced quote for technical acceptability in accordance with the solicitation. If the lowest priced quote is determined not to be technically acceptable, the next lowest quote will be evaluated and so on, until one is found to be technically acceptable. When combined, the Technical Approach Document and Past Performance will be the only basis for NNSY Technical Evaluators rating of �acceptable� or �unacceptable�; see below for details. Technically acceptable specifications are for the calibration of gage blocks and in accordance with Attachment 1 � Statement of Work. A Technical Approach Document - Past Performance are required. The Past Performance section shall supplement the Technical Approach when being evaluated by the NNSY Technical Evaluators. Technical Approach: Doc shall state how the contractor intends to complete the work as stated in the SOW/PWS in as much or as little detail as they believe required. Past Performance: Contractors shall submit past performance that is recent, (within 5 years) and relevant, (Technical Evaluator�s Discretion) to this requirement, and within a similar scope of magnitude, (Technical Evaluator�s Discretion). Format: Technical Approach and Past Performance documents can be submitted in Word, Excel, or PDF format. Limitations: Each element, (Technical/Past Performance) will not exceed two (2) pages in length, no more than four (4) when combined. Font will not be smaller than 10pt. Documents which contain any Contractor identifying information or price may be deemed technically unacceptable and not considered for award: Price, will be evaluated on a comparative basis amongst all received quotations and the Government�s ��estimate. All price quotations and contractor information must be submitted on Attachment 2 - Quote Sheet, and it must be filled in entirely. Attachments Attachment 1 � Statement of Work Attachment 2 � Quote Sheet Attachment 3 � NNSY CONTRACT REQUIREMENTS Attachment 4�� N4215823QN026
Web Link: SAM.gov Permalink
(https://sam.gov/opp/5ef2d6e61ba24e64bf1c222a6526a2c0/view)
Place of Performance: Address: Portsmouth, VA 23709, USA; Zip Code: 23709; Country: USA
Record: SN06592241-F 20230217/230215230113 (samdaily.us)
Source: SAM.gov Link to This Notice
(may not be valid after Archive Date)

| FSG Index | This Issue's Index | Today's SAM Daily Index Page |

Loren Data's SAM Daily™

J -- Gage Block Calibration