Loren Data's SAM Daily™

fbodaily.com
Home Today's SAM Search Archives Numbered Notes CBD Archives Subscribe
SAMDAILY.US - ISSUE OF DECEMBER 08, 2022 SAM #7678
SOLICITATION NOTICE

61 -- Wire Bundles

Notice Date
12/6/2022 9:39:05 AM
 
Notice Type
Solicitation
 
NAICS
33592 —
 
Contracting Office
ARGONNE NATL LAB - DOE CONTRACTOR Lemont IL 60439 USA
 
ZIP Code
60439
 
Solicitation Number
3-B138-Q-00093-00
 
Response Due
12/9/2022 3:00:00 PM
 
Archive Date
12/24/2022
 
Point of Contact
Kendra Spencer, Phone: 6302526829
 
E-Mail Address
kcspencer@anl.gov
(kcspencer@anl.gov)
 
Description
See Statement of Work for further details. The Advanced Photon Source Upgrade Project (APSU) is planning a storage-ring upgrade that will reduce the electron-beam emittance by a factor of ~75. This ultra-low emittance is achieved by replacing the present storage ring lattice with a multi-bend achromat (MBA) lattice. �The APS-U storage ring a contains vacuum system that shall operates at ultra-high vacuum (UHV) pressures near 10-9 torr. The vacuum system will require an in-situ �bake� of all vacuum chambers to temperatures up to 180 C in order to purge internal gases. The bake will be performed in-situ using a variety of electrical heaters powered by temperature regulated power distribution carts as diagrammed in Figure 1.2. The heaters, power distribution carts and the temperature control carts are not part of this SOW scope. There is a total of (46) individual heater circuits per sector that are energized simultaneously for a complete bake-out.� These circuits are categorized into a family of nine (9) unique types of wiring Kits, with each Kit consisting of a number of individual Bundles of similar wiring contents.� Each bundle will provide the connections for one branch circuit.� Each branch circuit layout is in either a single, series, or parallel configuration, as to balance the electrical load of the electrical heaters between each circuit.� � � � �1.Material Requirements The following are requirements for the material specified in the kitted bundles. If there are supply chain issues with any of the following materials the contractor can propose alternative equivalents for APSU approval. � � � 2. Wire Requirements The following are requirements for the wires specified in the kitted bundles. � � � 3. Power, Neutral, and Ground Wire Size The wire for the bundles shall be #14 AWG / 19 strand count wire conductor. Sheathing Insulation Requirements The sheathing shall conform to MIL-W-22759/16 for sufficient radiation resistance for the life expectancy of the Storage Ring. The sheathing shall be constructed of ETFE (ethylene-tetraflouroethylene).�� Color The colors of the wire shall be designated: �������������� Neutral - White �������������� Phase / Line � Blue �������������� Ground � Green Thermocouple Wire Size The thermocouple wire for the bundles shall be Type K Duplex Thermocouple Wire, 20 AWG solid. Sheathing Insulation Requirements The sheathing shall conform to MIL-W-22759/16 for sufficient radiation resistance for the life expectancy of the Storage Ring. The sheathing shall be constructed of ETFE (ethylene-tetraflouroethylene).�� � � � � 4.Connectors Power Plugs The three blade power plug shall be equivalent to Hubbell #HBL5366C 3-Blade Straight Plug, Grounded, NEMA 5-20 Thermocouple connector The thermocouple connector shall be equivalent to McMaster #3869K25 Thermocouple Connector, Round-Pin Male, Screw Terminal, Type K, 400�F Maximum � � � �5. Flexible Metal Conduit and Adapters Flexible Metal Conduit The flexible metal conduit shall be equivalent to McMaster #74115K2 Flexible Metal Conduit, Flexible Zinc-Plated Steel, 3/8 Trade Size Grommet The grommet for the flexible metal conduit shall be equivalent to McMaster #8216K42 3/8 Trade Size Female Grommet for Flexible Metal Conduit and Armored Cable Adapter The adapter for the flexible metal conduit shall be equivalent to McMaster #7969K21 Adapter for Flexible Metal Conduit and Armored Cable, Zinc Push-In Straight, 3/8 x � Heat Shrink The heat shrink for the flexible metal conduit shall be equivalent to McMaster #6552N28 Tapered Heat-Shrink Tubing, 1.12"" ID Before Shrinking, 2.2"" Long, Non Lipped End
 
Web Link
SAM.gov Permalink
(https://sam.gov/opp/31ec4e5a41084c9fa300de7efa0a07b1/view)
 
Record
SN06536360-F 20221208/221206230058 (samdaily.us)
 
Source
SAM.gov Link to This Notice
(may not be valid after Archive Date)

FSG Index  |  This Issue's Index  |  Today's SAM Daily Index Page |
ECGrid: EDI VAN Interconnect ECGridOS: EDI Web Services Interconnect API Government Data Publications CBDDisk Subscribers
 Privacy Policy  Jenny in Wanderland!  © 1994-2024, Loren Data Corp.