SOURCES SOUGHT
84 -- Face Covering
- Notice Date
- 9/17/2020 2:45:30 PM
- Notice Type
- Sources Sought
- NAICS
- 315210
— Cut and Sew Apparel Contractors
- Contracting Office
- DLA TROOP SUPPORT PHILADELPHIA PA 19111-5096 USA
- ZIP Code
- 19111-5096
- Solicitation Number
- SPE1C120R0TBA
- Response Due
- 9/21/2020 12:00:00 AM
- Archive Date
- 09/23/2020
- Point of Contact
- Monique PORTER215-737-3884
- E-Mail Address
-
MONIQUE.PORTER@DLA.MIL
(MONIQUE.PORTER@DLA.MIL)
- Description
- This Sources Sought is posted to seek�interested�vendors to manfacture and deliver Face Coverings as decribed below the requirement. The anticipated requirement for this item is as follows: Lot 1: Maximum Dollar Value $6.5M Lot 2: Maximum Dollar Value $6.5M PLEASE NOTE: OFFERED PRODUCTS MUST BE MANUFACTURED DOMESTICALLY FROM 100% DOMESTIC PRODUCTS.� If interested, please submit an estimated (FOB Destination) unit price for each lot to DLATSFACEMASKS@DLA.MIL. DO NOT email the Point of Contact listed on this annoucement. This information�will be used for MARKET RESEARCH PURPOSES ONLY and does NOT constitute a proposal. Product Description for Cover, Face�� ���������������������������� 17 September 2020 Scope The Contractor shall provide all necessary material and equipment in order to manufacture cloth face covers for individual wear. �Note that the face cover is intended to provide a basic level of protection from the spread of viruses such as Coronavirus/COVID-19.� The face cover is not intended to replace surgical masks, N-95 respirators, or other medical devices.� Face cover designs should comply with the Center for Disease Control and U.S. Surgeon General�s guidelines on cloth face covers (https://www.cdc.gov/coronavirus/2019-ncov/prevent-getting-sick/diy-cloth-face-covers.html). � Size Face covers are one size fits all � Salient Characteristics The face cover shall be made of at least two layers of cloth.� The face cover shall cover the user�s face from nose to chin, and shall fit snugly but comfortably against the side of the face. The face cover shall feature ear loops, made of elastic or other textile materials, which will be used to secure the face cover to the user�s face.� Construction and materials shall allow for breathing without restriction, and shall not restrict the User�s vision or movement.� The air permeability of the face cover shall be 25 cubic feet per minute per square foot minimum when tested in accordance with ASTM D737.� The air permeability requirement applies throughout the life cycle of the face cover (initially and after re-use.)� The face cover shall be able to be used multiple times without damage to, or change in fitment of, the face cover.� The face cover shall be solid in color, and shall not contain any writing, logos, or designs on the exterior (visible) portion of the face cover.� The face cover shall not contain any anti-microbial or anti-viral finishes or chemicals.� Face covers shall be a neutral color.� Material: The base material shall be cloth (woven, non-woven, and/or knitted cloth are acceptable) that has been shown to be non-irritating and non-toxic to the user.� The design shall incorporate multiple layers of cloth over the face portion of the face cover (not including bindings, hems, or ear loops.)� Color requirements for the face cover(s) will be specified in the procurement document(s).� Toxicity Requirements: The contractor is responsible and must assure that all components are made from non-toxic materials. The Government reserves the right to verify that components are non-toxic in accordance with the following: a. Title 40 Code of Federal regulations, current Edition and applicable sections. b. As an alternative to animal and human testing, the contractor may provide information which certifies that components are composed of chemicals and/or materials which have been safely used commercially were prolonged skin contact has occurred. The Contractor shall provide one set of instructions for proper care and use in each unit pack.� If the face cover is intended to be laundered, detailed laundering instructions shall be included.� Certificate of Compliance (CoC) for all components shall be acceptable for verification of the materials used.� The Government reserves the right to require the Contractor to furnish test reports to validate materials or other technical requirements.� � SECTION D � PACKAGING AND MARKING��� One Case has 500 face covers. PRES/PACK C/C TO ASTM-D-3951 Packaging shall be as per ASTM-D-3951 and MIL-STD-147. Pallet shall be 4-way entry type and wing type.� Packaging examination.� The fully packaged end item shall be examined for the defects listed below.� The lot size shall be expressed in units of shipping containers.� The sample unit shall be one shipping container fully packaged.� The Inspection level shall be S-2 and the AQL, expressed in terms of defects per hundred units, shall be 2.5. Examine������������� Defect Marking (exterior)���� ������� & Unit Pack ������� Omitted; incorrect; illegible, of improper size, location, sequence �������������������� or method of application. Materials���� ����� Any component missing, damaged �������������� ���� or not as specified. Workmanship���� ��� Inadequate application of components, ������������� ����� such as: incomplete closure of �������������� ���� container flaps, loose strapping, �������������� ���� improper taping, or inadequate �������������� ���� stapling. Bulged or distorted �������������� ���� container. Contents���� ������ Number of intermediate containers �������������� ���� per shipping container is more or �������������� ���� less than required. �������������� ���� Number of items per container is �������������� ���� more or less than required. Palletization examination.� The fully packaged and palletized end items shall be examined for the defects listed below.� The lot size shall be expressed in units of palletized unit loads.� The sample unit shall be one palletized unit load, fully packaged. The Inspection level shall be S-1 and the AQL, expressed in terms of defects per hundred units, shall be 6.5. Examine�������������� Defect Finished�������� Length, width or height exceeds���������������� Dimensions������ specified maximum requirement. Palleti-�������� Pallet pattern not as specified. zation���������� Interlocking of loads not as ���������������� specified. Load not bonded with ���������������� required straps as specified. Weight���������� Exceeds maximum load limits. Marking��������� Omitted; incorrect; illegible; ���������������� of improper size, location, ���������������� sequence or method of appli- ���������������� cation. MIL-STD-147E w/CHANGE 1 23 December 2013 SUPERSEDING MIL-STD-147E 16 May 2008 DEPARTMENT OF DEFENSE STANDARD PRACTICE PALLETIZED UNIT LOADS Important Note on Foreign Content: The Defense appropriations and authorization acts and other statutes (including what is commonly referred to as ""The Berry Amendment"" impose restrictions on the DoD's acquisition of foreign products and services. Generally, Clothing and Textile items (as defined in DFARS clause 252.225-7012) and ""specialty metals"" (as defined in DFARS clause 252.225-7014) must be grown, reprocessed, reused, melted or produced in the United States, its possessions or Puerto Rico, unless one of the DFARS 225.7002-2 exceptions applies.
- Web Link
-
SAM.gov Permalink
(https://beta.sam.gov/opp/f81b8c92b93544d090907bfde9114a80/view)
- Place of Performance
- Address: Philadelphia, PA 19111, USA
- Zip Code: 19111
- Country: USA
- Zip Code: 19111
- Record
- SN05802582-F 20200919/200917230217 (samdaily.us)
- Source
-
SAM.gov Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's SAM Daily Index Page |