SOLICITATION NOTICE
34 -- OMAX Waterjet
- Notice Date
- 9/8/2020 12:51:01 AM
- Notice Type
- Combined Synopsis/Solicitation
- NAICS
- 423830
— Industrial Machinery and Equipment Merchant Wholesalers
- Contracting Office
- FA5606 52 CONS DA LGC APO AE 09126-3910 USA
- ZIP Code
- 09126-3910
- Solicitation Number
- FA5606-20-Q-2015
- Response Due
- 9/16/2020 5:30:00 AM
- Archive Date
- 10/01/2020
- Point of Contact
- Stephen L. Ortiz-Gonzalez, Phone: 496565617717, Bryan Driscoll, Phone: 496565619544
- E-Mail Address
-
stephen.ortiz-gonzalez@us.af.mil, bryan.driscoll.3@us.af.mil
(stephen.ortiz-gonzalez@us.af.mil, bryan.driscoll.3@us.af.mil)
- Description
- The 52d MXG is requesting an OMAX abrasive Water Jet to be used for manufacturing and modeling. Please� see listing below for a full description of the required items. This requirement is to fit existing in components already in place and the system must have an AFNET certification by the Air Force Security Control Assessor which the software on this version of the OMAX abrasive Water Jet has. OMAX WaterJet Machining Center Model 55100 Brand name 1. Machine will be approximately 12' 11"" by 7' 10"" with maximum supported load of 400 lbs per sq ft, table size 10' 6"" by 5' 5"", 3 Phase 380-480VAC +-110%, 50-60Hz 2. Machine will be able to cut materials up to 4ft by 8ft 3. 600 lb Bulk Abrasive Hopper 4. Direct Drive Pump- 30 horsepower, output pressure, 60,000psi, maximum jet power 25.5 horsepower, 5. One piece integrated nozzle warranted for 500 hours, 6. Pallet of Garnet abrasive, approx 2200 lbs. 7. Meets and exceeds the federally mandated green energy requirement Additional Components 1. Tilt a Jet 2. Variable Speed Solids Removal System 3. WRS Consumables Kit, Closed Loop System 4. Water Recycle System w/ 60,000 BTU/HR (5 Ton) Chiller and Laminar Filter, Single Pump 5. Material holding Kit 6. Nozzle Spare Parts Kit, Tilt-A-Jet, 5i 7. Basic Enduro MAX Pump Spares 8. Rotary Axis 9. Rotary Axis - ER40 Collet Adapter Kit 10. Rotary Axis - Universal Adapter Flange Kit 11. Unlimited Seats of Software 12. Software Upgrades for the Life of Machine 13. Pertinent Trainings Question 1.���In one line it says a table size of 10� 6� by 5� 5�, but in the next it says �cut materials up to 4ft by 8ft�. I just wanted to know which one is correct? Response�1.���Water Jet must be able to cut metal up to 4ft by 8ft sheets. Our recommendation to fit a full sheet of metal is a table size at least 10�6� by 5�5�.
- Web Link
-
SAM.gov Permalink
(https://beta.sam.gov/opp/6529e85198814de2a7701a4fed7e85e1/view)
- Place of Performance
- Address: spangdahlem, DEU
- Country: DEU
- Country: DEU
- Record
- SN05789856-F 20200910/200908230154 (samdaily.us)
- Source
-
SAM.gov Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's SAM Daily Index Page |