SOURCES SOUGHT
25 -- 1 NSN 2530-01-104-8941 Parts Kit
- Notice Date
- 1/23/2020 1:17:57 PM
- Notice Type
- Sources Sought
- NAICS
- 336992
— Military Armored Vehicle, Tank, and Tank Component Manufacturing
- Contracting Office
- DLA LAND AND MARITIME COLUMBUS OH 43218-3990 USA
- ZIP Code
- 43218-3990
- Solicitation Number
- 1000083470
- Response Due
- 1/30/2020 12:00:00 PM
- Archive Date
- 02/14/2020
- Point of Contact
- Amanda Stroupe, Phone: 6146923116
- E-Mail Address
-
Amanda.Stroupe@dla.mil
(Amanda.Stroupe@dla.mil)
- Description
- Sources Sought Notice: DLA Land and Maritime is preparing to solicit an Indefinite Delivery Contract (IDC) for NSN 2530-01-104-8941 Parts Kit.�Sources interested in this solicitation should complete the attached Market Survey and return the competed copy to Amanda Stroupe at Amanda.stroupe@dla.mil within 5 business days of this posting.� PID: REPAIR KIT, VEHICULAR WHEEL. RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT EXPORT CONTROL OF TECHNICAL DATA: This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce.� Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad.� This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data. The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data.� Instructions for obtaining access to the export-controlled data can be found at: https://www.dla.mil/HQ/LogisticsOperations/EnhancedValidation/ To be eligible for award, offerors and any sources of supply proposed for use are required to have an approved JCP certification and have been approved by the DLA controlling authority to access export-controlled data managed by DLA.� DLA will not delay award in order for an offeror or its supplier to apply for and receive approval by the DLA controlling authority to access the export-controlled data. RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS.� FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS. RQ001: HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND NON-MANUFACTURERS) RQ002: CONFIGURATION CHANGE MANAGEMENT - ENGINEERING CHANGE PROPOSAL REQUEST FOR VARIANCE (DEVIATION OR WAIVER) RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES RQ016: COMPONENT QUALIFIED PRODUCTS LISTS (QPL)/QUALIFIED MANUFACTURERS LISTS (QML).� THIS ITEM CONTAINS ONE OR MORE COMPONENTS DEFINED BY A SPECIFICATION(S) WITH AN ASSOCIATED QUALIFIED PRODUCTS LIST (QPL) OR QUALIFIED MANUFACTURERS LIST (QML).� QUALIFICATION REQUIREMENTS IN PROCUREMENT NOTE H02 ""COMPONENT QUALIFIED PRODUCTS LIST (QPL)/QUALIFIED MANUFACTURERS LIST (QML)"" APPLY. CERTIFICATE OF CONFORMANCE PROCEDURES (FAR 52.246-15) ARE AUTHORIZED, UNLESS WITHELD BY A QUALITY ASSURANCE LETTER OF INSTRUCTION. SAMPLING: THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT. ""THIS NSN CONTAINS ONE OR MORE COMPONENTS WHICH MUST CONFORM TO SOURCE CONTROL DRAWING. BY SUBMITTING AN OFFER, THE OFFEROR AGREES TO PROVIDE SOURCE CONTROLLED COMPONENTS FROM SOURCES APPROVED ON THE APPLICABLE SOURCE CONTROL DRAWING."" CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE USED NOR INCORPORATED IN ANY ITEMS TO BE DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS. SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR APPROVAL UNLESS THEY ARE AUTHORIZED BY THE SPECIFICATION REQUIREMENTS. ""FINAL INSPECTION AND ACCEPTANCE OF THE ITEM SHALL BE AT THE ACTUAL MANUFACTURING FACILITY. TECHNICAL INSPECTION IS REQUIRED.� THE CONTRACTOR SHALL MAKE DRAWINGS AND TECHNICAL INFORMATION AVAILABLE TO VERIFY THAT THE ITEM MEETS ALL TECHNICAL REQUIREMENTS. COUNT, KIND, AND CONDITION INSPECTIONS ARE NOT ACCEPTABLE.� THIS NOTE TAKES PRECEDENCE OVER MASTER SOLICITATION PART ONE PROVISIONS, NOTE 6, QUOTATIONS BY NON-MANUFACTURERS (APR 1984, DCSC 52.217-9C01). FINAL INSPECTION OF PACKAGING, IF REQUIRED, MAY BE CONDUCTED ELSEWHERE."" CRITICAL APPLICATION ITEM IAW BASIC DRAWING NR 19207 12295593 REVISION NR B�� DTD 09/04/1992 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12295289 REVISION NR L�� DTD 09/14/1995 PART PIECE NUMBER: IAW REFERENCE QAP 19207 12295289 REVISION NR F�� DTD 08/30/1990 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12296926 REVISION NR D�� DTD 06/08/1983 PART PIECE NUMBER: IAW REFERENCE QAP 19207 12296926 REVISION NR���� DTD 09/24/1981 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12295552 REVISION NR E�� DTD 06/13/1990 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12369857 REVISION NR���� DTD 08/28/1990 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12295593 REVISION NR A�� DTD 12/15/1992 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12296766 REVISION NR C�� DTD 07/02/1998 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 12295593 REVISION NR���� DTD 12/02/2019 PART PIECE NUMBER: Packaging: PKGING DATA - MIL-STD-2073-1D, 15 DEC 1999 QUP:001� PRES MTHD:ZZ� CLNG/DRY:1� PRESV MAT:00 WRAP MAT:DA� CUSH/DUNN MAT:NA� CUSH/DUNN THKNESS:A UNIT CONT:D3� OPI:M INTRMDTE CONT:E5� INTRMDTE CONT QTY:100 PACK CODE = Q: PACKING LEVEL = B: MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129. SPECIAL MARKING CODE:ZZ -ZZ Special Requirements PALLETIZATION SHALL BE IN ACCORDANCE WITH MD00100452 REV B DATED JULY 01, 2008 ""PRESERVATION & PACKAGING SHALL BE I/A/W THE LATEST REVISION OF MILITARY SPECIFICATION MIL-STD-2073-1 APPENDIX D, FOR PACKAGING OF ""KITS"". PER MIL-STD-2073-1D, APPENDIX D, PARAGRAPH D.3.1.b: METHOD OF PRESERVATION SHALL AFFORD ADEQUATE PROTECTION TO THE MOST CRITICAL ITEM CONTAINED WITHIN THE KIT. NOTE: All loose hardware shall be contained within a sealed container (bag/box) and the highest applicable preservation method (based on physical characteristics of items) shall be applied to ensure items will not be damaged or experience corrosion. In addition, packaged hardware shall be placed within each individual unit container to ensure items do not damage (dent, scratch, nick, etc.) the part or any components therein. NOTE: Hardware for shipments cannot be shipped in bulk. It is not an acceptable practice. Material must arrive in serviceable condition and meet the contractual quantity unit pack requirements. Thus, requiring no additional sorting, packaging, and/or marking by user or depot personnel. ADDITIONAL SPECIAL MARKING REQUIREMENTS: SEGREGATION AND INDIVIDUAL IDENTIFICATION REQUIREMENTS ARE LISTED IN MIL-STD-2073-1, APPENDIX D, PARAGRAPH D.4.2. A PARTS LIST (WITH PART NAME, PART NUMBER & QUANTITY) SHALL BE INCLUDED WITHIN EACH KIT. IF APPLICABLE, ASSEMBLY INSTRUCTIONS SHALL ALSO BE INCLUDED WITHIN EACH PACKAGE. IP025: PACKAGING, MARKING, AND SHIPPING OF HAZARDOUS MATERIALS AMC 1 � Competitive Acquisition AMSC C- Part (s) require engineering source approval
- Web Link
-
SAM.gov Permalink
(https://beta.sam.gov/opp/33b31a3219564cb3a4fa6af353961482/view)
- Record
- SN05542359-F 20200125/200123230140 (samdaily.us)
- Source
-
SAM.gov Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's SAM Daily Index Page |