Loren Data's SAM Daily™

FBO DAILY - FEDBIZOPPS ISSUE OF OCTOBER 31, 2014 FBO #4724
SOLICITATION NOTICE

10 -- BARREL ASSEMBLY

Notice Date

10/29/2014
 

Notice Type

Presolicitation
 

NAICS

332994 — Small Arms, Ordnance, and Ordnance Accessories Manufacturing
 

Contracting Office

Defense Logistics Agency, DLA Acquisition Locations, DLA Land and Maritime, P O Box 3990, Columbus, Ohio, 43218-3990, United States
 

ZIP Code

43218-3990
 

Solicitation Number

SPE7L415R0010
 

Archive Date

12/30/2014
 

Point of Contact

Michele Beasley, Phone: 6146927572
 

E-Mail Address

michele.beasley@dla.mil
(michele.beasley@dla.mil)
 

Small Business Set-Aside

N/A
 

Description

NSN# 1005-01-146-7684 / 2300 EA W/100% OPTION OPEN/CLOSE: 11/13/14 - 12/15/14 ********************************************************* BARREL ASSEMBLY DLAD Clause 52.209-9033, Qualified Suppliers List of Manufacturers (QSLM) - FSCs 1005 (Guns, through 30 mm), 1010 (Guns, over 30 mm through 75 mm), 1015 (Guns, over 75 mm through 125 mm), 1020 (Guns, over 125 mm through 150 mm), 1025 (Guns, over 150 mm through 200 mm), 1055 (Launchers, rocket and pyrotechnic), and 1095 (Miscellaneous weapons), applies. Only manufacturers listed or qualified for listing on the QSLM at the time of award, or authorized distributors with adequate traceability to a QSLM qualified manufacturing source, are eligible to receive an award. The full text of DLAD Clause 52.209-9033 and a listing of QSLM qualified manufacturing sources can be viewed electronically at: http://www.landandmaritime.dla.mil/offices/ sourcing_and_qualification/offices.aspx?Section=QSA. The provisions and criteria required for qualification, approval, and listing on the DLA Land & Maritime QSLM - Gun Parts are also available on the website. THIS ITEM IS A "DEFENSE ARTICLE" AS DEFINED IN AND SUBJECT TO THE INTERNATIONAL TRAFFIC IN ARMS REGULATIONS (22 C.F.R. 120-30) AND THE ARMS EXPORT CONTROL ACT (22 U.S.C.A. 2778-2799). ANY MANUFACTURER OR EXPORTER OF DEFENSE ARTICLES IS REQUIRED TO REGISTER WITH THE DIRECTORATE OF DEFENSE TRADE CONTROLS (DDTC), DEPARTMENT OF STATE. DOCUMENTARY EVIDENCE OF REGISTRATION MAY BE REQUIRED PRIOR TO AWARD. ADDITIONAL EXPORT RESTRICTIONS APPLY AS INDICATED HEREIN. FAILURE TO SUBMIT DDTC REGISTRATION WHEN REQUESTED WILL MAKE A QUOTE/OFFER INELIGIBLE FOR AWARD. _______________EXCEPTION DATA____________________ SAFETY COMMENTS: Add the following HCSDS: HCSDS - 1728, Rev - U, Date - 02/07/13, Nomenclature - CARTRIDGE,5.56MM,BALL,M855 -------------------------------------------------- QUALITY: ADD DISTRIBUTION STATEMENT "F" TO QS DOCUMENTS Part Number Cancelled SPEC 8448202 MIL-STD-120 CAN BE USED FOR INFORMATION ONLY IF DRAWING NOTE GIVES OPTION FOR ZINC OR MANGANESE COATING THEN MANGANESE IS REQUIRED. ______________END OF EXCEPTIONS__________________ _________SPECIAL GFE AND GFM REQUIREMENTS_________ THIS ITEM REQUIRES GOVERNMENT FURNISHED EQUIPMENT (GFE) AND GOVERNMENT FURNISHED MATERIAL (GFM). SEE BELOW FOR SPECIAL CONTRACT REQUIREMENTS: A. EQUIPMENT REQUIRED FOR CONTRACTOR'S USE: 1. 5 EACH - M16A2, NSN - 1005-01-128-9936. B. A security preaward survey is required for these items. DFARS, Part 252.223-7007, "Safeguarding Sensitive Conventional Arms, Ammunition, and Explosives," shall be part of the solicitation/ contract. C. This contract involves HAZARDOUS MATERIAL. DFARS 252.223.7002, Safety Precautions for Ammunition and Explosives, DFARS 252.223.370-4, PGI 223.370-4(1)(iv), Safety Precautions for Ammunition and Explosives - PREAWARD SURVEY, and DFARS 252.223.370-4, PGI 223.370-4(1)(iii), Disposal of Remaining GFM Ammunition and Explosives Following Contract Completion or Termination Instructions, shall be part of the solicitation/contract. _______END SPECIAL GFE AND GFM REQUIREMENTS_______ THE ITEM BEING PROCURED IS A CRITICAL GUN PART ITEM WITH UNIQUE REQUIREMENTS. CONTRACTOR FAT APPLIES. PER FAR 52.209-3: (a) THE CONTRACTOR SHALL TEST 5 UNIT(S)... AT LEAST 10 CALENDAR DAYS BEFORE THE BEGINNING OF FIRST ARTICLE TESTING, THE CONTRACTOR SHALL NOTIFY... (b) THE CONTRACTOR SHALL SUBMIT THE FAT REPORT WITHIN 90 CALENDAR DAYS... (NOTE: THE DELIVERY SCHEDULE ON THE FACE OF THE SOLICITATION REFLECTS ONLY THE TIME TO DELIVER THE SUPPLIES.) WITHIN 45 CALENDAR DAYS AFTER THE GOVERNMENT RECEIVES THE FIRST ARTICLE THE CONTRACTING OFFICER SHALL NOTIFY... DISPOSITION OF FIRST ARTICLES: THE CONTRACTOR MAY DELIVER APPROVED UNDAMAGED FIRST ARTICLE SAMPLES AS PART OF THE PRODUCTION QUANTITY. AFTER RECEIPT OF QUOTES, OFFERORS MAY BE CONTACTED TO PRICE THE FAT REQUIREMENT. PROCESS PROCEDURES AND OR WORKMANSHIP SPECIMENS REQUIRED BY MILITARY SPECIFICATION (S) APPLICABLE TO THIS CONTRACT WILL BE APPROVED BY THE CONTRACT POST AWARD CONTRACTING OFFICER (PCO). PRODUCT INSPECTION WILL BE CONDUCTED BY THE DCMA QAR AT THE ACTUAL MANUFACTURER'S FACILITY. THE IDENTIFICATION OF THE ACTUAL MANUFACTURER AND PHOSPHATE CONTRACTOR MUST BE SUBMITTED TO THE CONTRACTING OFFICER FOR INCLUSION IN THE AWARD. UPON AWARD, ANY CHANGES TO THE ABOVE MUST BE APPROVED BY THE PCO VIA FORMAL CONTRACT MODIFICATION. THIS NSN CONTAINS ONE OR MORE COMPONENTS WHICH MUST MEET QPL/QML SPECIFICATIONS AS IDENTIFIED IN THE TECHNICAL DATA PACKAGE. CLAUSE I09A01 (FAR CLAUSE 52.209-1) QUALIFICATION REQUIREMENTS IS APPLICABLE. THE AWARDEE SHALL PROVIDE QPL/QML COMPONENTS ONLY FROM SOURCES QUALIFIED ON THE APPLICABLE QPL(S)/QML(S). THE IDENTIFICATION OF ALL APPLICABLE QPL/QML SOURCES MUST BE SUBMITTED TO THE CONTRACTING OFFICER FOR EVALUATION PRIOR TO CONTRACT AWARD. PRODUCT VERIFICATION TESTING (PVT) CLAUSE DLAD 52.246-9004 MAY BE INVOKED FOR THE REFERENCED CONTRACT. IF INVOKED, PVT SAMPLES MUST BE INSPECTED, PACKAGED AND MARKED AS REQUIRED IN THE CONTRACT. ONE (1) SAMPLE MAY BE DESTROYED DURING TESTING. PRODUCT VERIFICATION TESTING, IF INVOKED, WILL BE PERFORMED PRIOR TO ACCEPTANCE OF EACH SHIPMENT. THE CONTRACTOR MUST PROVIDE PVT SAMPLES FROM EACH (SUB)CONTRACTOR USED IN THE PRODUCTION OF PARTS ON THIS CONTRACT. FIVE (5) PVT SAMPLES, UNLESS OTHERWISE SPECIFIED, WILL BE REQUIRED TO BE IDENTIFIED TO THOSE (SUB)CONTRACTORS WHEN THEY ARE SENT IN FOR TESTING. CERTIFICATE OF CONFORMANCE IS NOT AUTHORIZED. 52.246-11 Higher Level Contract Quality Requirement (Manufacturers) FAR CLAUSE 52.246-11 APPLIES. A QUALITY MANAGEMENT PROGRAM MEETING THE REQUIREMENTS OF ISO 9001:2008; A PROGRAM COMPARABLE TO ISO 9001:2008 (EXAMPLE SAE AS 9100), THE FOLLOWING TAILORED VERSION OF ISO 9001:2008; OR A PROGRAM COMPARABLE TO THE TAILORED VERSION OF ISO 9001:2008 (EXAMPLE SAE AS 9003) IS REQUIRED. MIL-I-45208 AND MIL-Q-9858 ARE OBSOLETE AND NO LONGER CONSIDERED SUITABLE WHEN HIGHER LEVEL QUALITY IS REQUIRED. IN THE TAILORED VERSION OF THE ISO 9001:2008, ANY REFERENCES WHICH CITE THE ENTIRE INTERNATIONAL STANDARD ARE INTERPRETED AS EXCLUSIONS TO THIS DOCUMENT. DLA TAILORED HIGHER LEVEL QUALITY CLAUSE FROM ISO 9001:2008 4.1 General requirements, [excluding reference to 1.2 and excluding NOTE 3 c)] 4.2.1 General, [excluding subparagraph a)] 4.2.2 Quality manual, [excluding subparagraph a)] 4.2.3 Control of documents 4.2.4 Control of records 5.1 Management commitment 5.3 Quality policy 6.2.2 Competence, training and awareness 6.4 Work environment 7.1 Planning of product realization, [excluding NOTE 2] 7.2.1 Determination of requirements related to the product 7.2.2 Review of requirements related to the product 7.2.3 Customer communication 7.3.7 Control of design and development changes 7.4.1 Purchasing process 7.4.3 Verification of purchased product 7.5.1 Control of production and service provision 7.5.3 Identification and traceability 7.5.4 Customer property 7.5.5 Preservation of product 7.6 Control of monitoring and measuring equipment 8.1 General, [excluding subparagraph b) and subparagraph c)] 8.2.2 Internal audit 8.2.4 Monitoring and measurement of product 8.3 Control of nonconforming product 8.5.2 Corrective action 8.5.3 Preventive action CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE USED NOR INCORPORATED IN ANY ITEMS TO BE DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS. SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR APPROVAL UNLESS THEY ARE AUTHORIZED BY THE SPECIFICATION REQUIREMENTS. DLAD 52.246-9003, MEASURING AND TEST EQUIPMENT, APPLIES. This item contains a phosphate coating requirement IAW MIL-STD-171 and MIL-DTL-16232. In lieu of the required submittal of a preproduction phosphate procedure the following is now required: The contractor responsible for the actual coating procedure must be certified by the Performance Review Institute (PRI) to the Nadcap standard for chemical processes. Verification of this certification may be required and must be supplied upon request of the Contracting Officer. THIS ITEM HAS TECHNICAL DATA SOME OR ALL OF WHICH IS SUBJECT TO EXPORT-CONTROL REGULATIONS. DISTRIBUTION OF THE TECHNICAL DATA AND ELIGIBILITY FOR AWARD ARE LIMITED TO THOSE SUPPLIERS QUALIFIED THROUGH JCP CERTIFICATION, OR TO THOSE LICENSED BY EITHER THE DEPARTMENTS OF STATE OR COMMERCE; OR TO FOREIGN SUPPLIERS PURSUANT TO INTERNATIONAL AGREEMENTS. TO APPLY FOR JCP CERTIFICATION, COMPLETE DD FORM 2345, "MILITARY CRITICAL TECHNICAL DATA AGREEMENT," FORM IS AVAILABLE AT THE WORLD WIDE WEB ADDRESS HTTP://WWW.DLIS.DLA.MIL/JCP OR BY WRITING TO: DLA LOGISTICS INFORMATION SERVICE FEDERAL CENTER 74 WASHINGTON AVE., NORTH BATTLE CREEK, MI 49037-3084 TO MANUFACTURE THIS ITEM, NON-JCP CERTIFIED SUPPLIERS MUST SUBMIT A CURRENT MANUFACTURING LICENSE AGREEMENT, TECHNICAL ASSISTANCE AGREEMENT, DISTRIBUTION AGREEMENT OR OFF-SHORE PROCUREMENT AGREEMENT APPROVED BY THE DIRECTORATE OF DEFENSE TRADE CONTROLS WITH THE OFFER, UNLESS AN EXEMPTION UNDER THE PROVISIONS OF ITAR SECTION, 125.4 "EXEMPTIONS OF GENERAL APPLICABILITY," AND/OR EAR PART 740 ARE APPLICABLE. NON-JCP CERTIFIED SUPPLIERS SEEKING EXPORT CONTROLLED TECHNICAL DATA ARE REQUIRED TO PROVIDE THE CONTRACTING OFFICER WITH AN APPLICABLE AGREEMENT OR IDENTIFY WHICH ITAR/EAR EXEMPTION APPLIES TO RECEIVE A COPY OF THE EXPORT CONTROLLED TECHNICAL DATA. NOTE: JCP CERTIFIED CONTRACTORS WHO RECEIVE TECHNICAL DATA PURSUANT TO THEIR DD FORM 2345 CERTIFICATION MAY NOT FURTHER DISSEMINATE SUCH DATA UNLESS FURTHER DISSEMINATION OF THE TECHNICAL DATA IS EXPRESSLY PERMITTED BY DODD 5230.25." MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL NOT BE INTENTIONALLY ADDED TO,OR COME IN DIRECT CONTACT WITH,ANY HARDWARE OR SUPPLIES FURNISHED UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS; AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA. PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR MERCURY COMPOUND. (IAW NAVSEA 5100-003D).,, DLAD PROVISION 52.211-9009 IS APPLICABLE TO THIS SOLICITATION, THEREFORE SURPLUS MATERIAL WILL NOT BE CONSIDERED. IF PRESENT IN THE SOLICITATION, PROVISION 52.211-9003 AND CLAUSE 52.211-9000 ARE NOT APPLICABLE.,, A forging process was identified as a means to manufacture this item. Tooling is required to produce a forging. For sourcing, tooling, materials or other information, please contact the appropriate assistance team: (Aviation, C&E Supply Chains) DSCR.AFCAT@dla.mil;(Land & Maritime Supply Chains) DSCC.cast.forge@dla.mil,, CLASS 3 THREADS APPLY TO THIS NSN.,, A metal casting process was identified as a means to manufacture this item. Tooling is required to produce a casting. For sourcing, tooling, materials or other information, please contact the appropriate assistance team: (Aviation, C&E Supply Chains) DSCR.AFCAT@dla.mil; (Land & Maritime Supply Chains) DSCC.cast.forge@dla.mil,, "THIS NSN CONTAINS ONE OR MORE COMPONENTS WHICH MUST CONFORM TO SOURCE CONTROL DRAWING. BY SUBMITTING AN OFFER, THE OFFEROR AGREES TO PROVIDE SOURCE CONTROLLED COMPONENTS FROM SOURCES APPROVED ON THE APPLICABLE SOURCE CONTROL DRAWING.",, "CONTRACTOR/MANUFACTURER IS REQUIRED TO ESTABLISH AND MAINTAIN A CALIBRATION SYSTEM THAT MEETS THE REQUIREMENTS OF ANSI/NCSL Z540-1-1994, AMERICAN NATIONAL STANDARD FOR CALIBRATION - CALIBRATION LABORATORIES AND MEASURING AND TEST EQUIPMENT-GENERAL REQUIREMENTS, OR ISO 10012-1, QUALITY ASSURANCE REQUIREMENTS FOR MEASURING EQUIPMENT- PART 1, METROLOGICAL CONFIRMATION SYSTEM FOR MEASURING EQUIPMENT.",, This item contains technical data that is not releasable to Foreign Nationals. To access the restricted technical data, vendors are required to complete and return the Foreign Secure certification form located in the DLA cFolders application located at: https://pcf1.bsm.dla.mi./cFolders,, A FN HERSTAL TECHNICAL DATA PACKAGE EXISTS FOR THIS ITEM. DATA NON-DISCLOSURE AND DATA DESTRUCTION CONDITIONS APPLY AND VENDORS MUST COMPLETE AND RETURN THE APPLICABLE FN HERSTAL CERTIFICATION FORMS WHICH ARE LOCATED IN THE DLA CFOLDERS APPLICATION: https://pcf1.bsm.dla.mil/cFolders,, PACKAGING SHALL BE IN ACCORDANCE WITH SPECIAL PACKAGING INSTRUCTION AM9349124. IAW BASIC DRAWING NR 19200 9349124 REVISION NR R DTD 11/06/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 11837943 REVISION NR K DTD 08/27/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 9349058 REVISION NR H DTD 01/15/2003 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19205 7266299 REVISION NR T DTD 02/01/2012 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19204 11837944 REVISION NR L DTD 11/19/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 8448510 REVISION NR AG DTD 12/17/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19204 8448643 REVISION NR M DTD 06/17/2009 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 9349053 REVISION NR E DTD 09/16/2004 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 9349054 REVISION NR AA DTD 11/19/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 9349056 REVISION NR L DTD 10/04/2007 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 8448503 REVISION NR M DTD 07/20/2010 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19204 8448550 REVISION NR T DTD 09/04/2008 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19204 8448551 REVISION NR G DTD 11/08/2004 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19204 8448553 REVISION NR J DTD 05/24/2002 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19204 8448574 REVISION NR H DTD 11/18/2009 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19204 8448575 REVISION NR K DTD 08/13/2004 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19204 8448649 REVISION NR E DTD 02/04/2013 PART PIECE NUMBER: IAW REFERENCE UNK QPL-3150-34 NOT 1 REVISION NR 34 DTD 10/03/2006 PART PIECE NUMBER: IAW REFERENCE UNK QPL-3420-28 NOT 1 REVISION NR 2 DTD 10/03/2006 PART PIECE NUMBER: IAW REFERENCE UNK QPL-16173-84 NOT 1 REVISION NR 84 DTD 10/03/2006 PART PIECE NUMBER: IAW REFERENCE UNK QPL-22750-6 NOT 1 REVISION NR 6 DTD 10/03/2006 PART PIECE NUMBER: IAW REFERENCE UNK QPL-23377-19 NOT 1 REVISION NR 19 DTD 10/03/2006 PART PIECE NUMBER: IAW REFERENCE UNK QPL-46010-18 NOT 1 REVISION NR 18 DTD 10/03/2006 PART PIECE NUMBER: IAW REFERENCE UNK QPL-46147-14 NOT 1 REVISION NR 14 DTD 10/03/2006 PART PIECE NUMBER: IAW REFERENCE UNK QPL-63460-32 NOT 1 REVISION NR 32 DTD 10/03/2006 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19204 8448573 REVISION NR L DTD 11/08/2005 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19204 8448571 REVISION NR U DTD 02/04/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 8448697 REVISION NR G DTD 09/02/2008 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 12579607 REVISION NR C DTD 08/04/2009 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19204 L2S3025 REVISION NR D DTD 05/03/2002 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 1728 REVISION NR U DTD 02/07/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 9342868 REVISION NR V DTD 03/24/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 R09Q2036 REVISION NR DTD 07/15/2009 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 L10S3093 REVISION NR 1 DTD 07/30/2010 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 L11S3031-SEVERAL REVISION NR DTD 04/14/2011 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13041260 REVISION NR DTD 02/01/2012 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19204 8448202 REVISION NR L DTD 10/12/2011 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 L12S3086 REVISION NR DTD 07/27/2012 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 9349124 REVISION NR DTD 04/21/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 12993884 REVISION NR G DTD 07/18/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 L13S3034 REVISION NR DTD 03/27/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 9349124-SPI REVISION NR DTD 01/31/2008 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 L13S3048 REVISION NR DTD 04/30/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 L13S3110 REVISION NR DTD 08/14/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 L13S3129 REVISION NR DTD 10/23/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 L13S3140 REVISION NR DTD 11/27/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 L14S3005 REVISION NR DTD 01/16/2014 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 R12Q2069 REVISION NR DTD 08/19/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 R13Q2030-1 REVISION NR DTD 09/26/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 R13S2046 REVISION NR DTD 11/04/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13011863 REVISION NR D DTD 02/05/2014 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13045512 REVISION NR DTD 12/17/2012 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13045513 REVISION NR A DTD 05/15/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13047419 REVISION NR DTD 11/19/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13047420 REVISION NR DTD 08/27/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13047421 REVISION NR DTD 08/27/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13047422 REVISION NR DTD 08/27/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13047423 REVISION NR DTD 08/27/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13047424 REVISION NR DTD 08/27/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13047425 REVISION NR DTD 08/27/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13047426 REVISION NR DTD 08/27/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13047427 REVISION NR DTD 08/27/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13047428 REVISION NR DTD 08/27/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13047429 REVISION NR DTD 08/27/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13047430 REVISION NR DTD 08/27/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13047431 REVISION NR DTD 08/27/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13047432 REVISION NR DTD 08/27/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13047433 REVISION NR DTD 08/27/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13047434 REVISION NR DTD 08/27/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 13052445 REVISION NR DTD 11/19/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 L13S3140 REVISION NR DTD 12/12/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 L13S3129 REVISION NR DTD 10/23/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 L13S3110 REVISION NR DTD 08/14/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 L13S3034 REVISION NR DTD 03/27/2013 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19200 9349124 REVISION NR DTD 05/14/2014 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 19207 L14S3096 REVISION NR DTD 06/12/2014 PART PIECE NUMBER:
 

Web Link

FBO.gov Permalink
(https://www.fbo.gov/spg/DLA/J3/DSCC/SPE7L415R0010/listing.html)
 

Record

SN03560781-W 20141031/141030000659-d71ddd486ed727210014d69d89a87da9 (fbodaily.com)
 

Source

FedBizOpps Link to This Notice
(may not be valid after Archive Date)

---

| FSG Index  |  This Issue's Index  |  Today's FBO Daily Index Page |