SOURCES SOUGHT
44 -- SECONDARY STEAM SYSTEM EQUIPMENT
- Notice Date
- 3/20/2012
- Notice Type
- Sources Sought
- NAICS
- 333414
— Heating Equipment (except Warm Air Furnaces) Manufacturing
- Contracting Office
- Department of Energy, Bechtel National, Inc. (DOE Contractor), Bechtel National Inc., 2435 Stevens Center Place, Richland, Washington, 99352
- ZIP Code
- 99352
- Solicitation Number
- 24590-CM-MRA-MS00-00022
- Response Due
- 10/10/2013
- Point of Contact
- Winifred Renz, Phone: 5093712338, ,
- E-Mail Address
-
werenz@bechtel.com,
(werenz@bechtel.com, /div)
- Small Business Set-Aside
- N/A
- Description
- Request for Interest Form Secondary Steam System Equipment Document Number: 24590-CM-MRA-MS00-00022 Important to Safety? No Quality Level: CM Quality Surveillance: LEVEL 2 - Limited Scope Inspection Commodity Code: MS00 NAICS Code: 333414 Submit Interest By: September 10, 2013 PROJECT DESCRIPTION AND LOCATION The Hanford Tank Waste Treatment and Immobilization Plant (WTP) is a complex of radioactive waste treatment processing facilities designed and constructed by Bechtel for the Department of Energy (DOE). The facility will process the Hanford Site tank waste and put the waste into a stable glass form. The processed waste will be shipped to other sites for depository. The Project site is located at 200 East Area of the Hanford Site near Richland, Washington, along the Columbia River. The site elevation varies from 662 to 684 feet above mean sea level. Sand and silt exist as surface materials. Ambient temperature is (-) 23 degrees F minimum to 113 degrees F maximum, with relative humidity of 5% minimum to 100% maximum. The project design life is 40 years. SCOPE OF WORK Design, procurement and fabrication of a Steam Generation System and Enclosure to form a steam generation facility. The facility will produce high pressure steam using recovered steam condensate for a Secondary Loop system. Supplier will use the attached flow-sheet to develop detailed system designs including final P&ID's, full instrumentation and control, pipe size and equipment size calculations, electrical design, structural design, equipment specifications, etc. to be able to build and supply a complete operable steam generating facility. (Ask Buyer for a copy of attachment.) The facility is to be designed and supplied in modules that will be installed by the BUYER at the jobsite Completed assembly is to have insulated and weather tight exterior to comply with BUYER's roofing and siding specifications. EQUIPMENT AND MATERIALS REQUIRED Heat Exchangers, Flash Vessel, Vent Condensers, Steam Separators, Blowdown Vessels, Stainless Steel / Carbon Steel pipe and associated isolation / control valves, structural steel for module framing, electrical wiring and conduit, lighting, roofing and siding, insulation, doors and finishes, etc. CODES & STANDARDS ASME B31.3 ASME B31.1 (Boiler Piping Only) ASME BPVC Section XIII ASME B16.5 AWS D1.1 ISO 1129 NFPA 70 NEMA 250 UL 50 IBC QA REQUIREMENTS Potential bidders should provide, in electronic format, some documentation that describes their company's Quality Assurance program. A summary, or table of contents of the program, similar evidence will be satisfactory. The information is to be uploaded directly into Bechtel's Supplier Database: https://supplier.bechtel.com The successful bidder must be registered with Bechtel and shall have and maintain a documented quality assurance program that complies with the applicable WTP requirements including, but not limited to, 10 CFR 830, DOE Order 414.1, ASME NQA-1. The bidder's Quality Assurance Program must meet the specific requirements of the Material Requisition. The bidder must have the ability to demonstrate satisfactory implementation of their Quality Assurance Program to be considered for an award. In order to expedite the qualification process, potential bidders are encouraged to provide a controlled copy of their Quality Assurance Program (include the "Package Ref." - Document Number) to the Buyer noted below, if controlled copy was not previously submitted and evaluated by BNI Supplier Qualification. The preferred method is to submit in electronic format via e-mail to: cdthomps@bechtel.com -or- Hard copies (include the "Package Ref." - Document Number) may be submitted to: Bechtel National, Incorporated Attn: Chris Thompson MS 5-G 2435 Stevens Center Place Richland, WA 99354 COMMERCIAL\TECHNICAL REQUIREMENTS Bechtel Procurement is responsible for collection, evaluation, and internal publication of Supplier/Subcontractor information through our project's pre-qualification program. In addition to the information requested above, Bechtel requires you to register your company at the Supplier and Contractor Portal at: https://supplier.bechtel.com Prior to being considered on any Bidders List you must go to the Qualification Process on this web site to complete the required forms for this opportunity. All information provided shall be strictly confidential. QUESTIONNAIRE Potential offeror shall submit their interest in this opportunity via e-mail using the "Submit Interest" link provided on the Two Year Forecast Report, which provides an outlined email including, but not limited to the bulleted items below, and is appropriately addressed to our central mailbox and to the buyer. Each interest email should include:  Dun and Bradstreet #:  Company Name:  Company Address:  Contact Phone #:  Contact Fax #:  Contact Person:  E-mail Address: Note: The wtpacqui@bechtel.com e-mail address is a document file address and is not an actual person. Bechtel personnel will access this address to see who has registered, but since it is not owned by any single person, do not send request for information to this address. If you require additional information, please contact the person listed in this posting. CONTACT Bechtel National, Inc. 2435 Stevens Center Place Richland, WA 99354 Attn: Christopher D. Thompson Mailstop: MS5-G Email: cdthomps@bechtel.com
- Web Link
-
FBO.gov Permalink
(https://www.fbo.gov/spg/DOE/BNI/BNI/24590-CM-MRA-MS00-00022/listing.html)
- Place of Performance
- Address: Work is to be perfomed at Suppliers place of business. (The facility is to be designed and supplied in modules that will be installed by the BUYER at the jobsite. Hanford Site, Richland, WA 99355), United States
- Record
- SN02701055-W 20120322/120320235729-cf1acf7c361910707b267dd1435f0b2c (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |