SOLICITATION NOTICE
J -- Annual Machine Tool Service Contract
- Notice Date
- 1/4/2012
- Notice Type
- Combined Synopsis/Solicitation
- NAICS
- 811310
— Commercial and Industrial Machinery and Equipment (except Automotive and Electronic) Repair and Maintenance
- Contracting Office
- USPFO for Connecticut, 360 Broad Street, Hartford, CT 06105-3795
- ZIP Code
- 06105-3795
- Solicitation Number
- W91ZRS12T0002
- Response Due
- 2/3/2012
- Archive Date
- 4/3/2012
- Point of Contact
- Jennifer Massicottee, 860 548 3267
- E-Mail Address
-
USPFO for Connecticut
(jennifer.h.massicotte@us.army.mil)
- Small Business Set-Aside
- Total Small Business
- Description
- This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in Subpart 12.6, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; proposals are being requested and a written solicitation will not be issued. The Army National Guard in Groton, Connecticut requires contract service/maintenance agreement for the following machine tools. The following maintenance checks and services are required to ensure that these machine tools are continuously operational. MANUAL MILLING MACHINES Bridgeport Series 1 Standard Milling Machine Serial Number: HJ315768 Greaves Cincinnati Milling Machine Model: 2XH Size 2 Serial Number: 149240 Remove Gibs, Clean, inspect and Readjust Install new way wipers if needed Inspect and Adjust All Straps Adjust Table, Saddle and Knee Gibs to proper specifications Adjust X and Y Axis Backlash Adjust High Gear Clutches in the Milling Head Check pump for proper operation, pressure etc. Clean Tank and Change Filter Inspect all way oil lines Change way oil manifolds or way oil injectors Check air regulator for leaks or faulty seals Check solenoids and air valves for leakage or malfunction Drain and clear water trap on air line filter Drain, clean and refill lubrication Check main pressure ATC Maintenance Remove covers and clean Check and adjust alignments Check slide and turret operation, and lubricate Check spindle belts Check spindle temperature and adjust chiller card Check chiller system and adjust, and clean pump filter, fill if necessary Check drawbar for proper retention and pressure at tool in/out (USE SVT0066) Check and adjust spindle tram Change Spindle Motor filter if applicable Check all connections, wires, boards, connectors etc. Check and adjust sin/cosine on clock card (DC machines only) Check ground integrity Adjust position loop gain Check and clean all fans for proper operation Check and fill all fluid levels Check and adjust rigid tapping if applicable Check scales if applicable CNC MILLING MACHINES Bridgeport 3 Axis CNC Milling Machine Model: EZ-Trak Serial Number: BR284274E Bridgeport 3 Axis CNC Milling Machine Model: EZ-Plus Serial Number: HDNG0411 Fadal5 Axis CNC Milling Machine Model: UMC5020A Serial Number: 012005027483 Remove Gibs, Clean, Inspect and Readjust Install new way wipers if needed inspect and Adjust All Straps Adjust Table, Saddle and Knee Gibs to proper specifications Adjust Axis Servo Cards for proper Balance, Current Gain and Velocity Gain Adjust Backlash through control software Adjust Lead Error Compensation Run check procedures for machines medium (C:>drive), Hard Drive, Flash, Disk On Chip, etc. Adjust High Gear Clutches in the Milling Head Check pump for proper operation, pressure etc. Clean Tank and Change Filter inspect all way oil lines Change way oil manifolds or way oil injectors Check air regulator for leaks or faulty seals Check solenoids and air valves for leakage or malfunction Drain and clear water trap on air line filter Drain, clean and refill lubrication Check main pressure ATC Maintenance Remove covers and clean Check and adjust alignments Check slide and tuner operation, and lubricate. Check spindle belts Check spindle temperature and adjust chiller card Check chiller system and adjust, and clean pump filter, fill if necessary Check drawbar for proper retention and pressure at tool in/out (USE SVT0066) Check and adjust spindle tram Change Spindle Motor filter if applicable Check all connections, wires, boards, connectors etc. Check and adjust sin/cosine on clock card (DC machines only) Check ground integrity Adjust position loop gain Check and clean all fans for proper operation Check and fill all fluid levels Check and adjust rigid tapping if applicable Check scales if applicable Advise on service items that need to be addressed CNC LATHE MACHINES Bridgeport CNC Lathe Model: EZ-Path-SD Serial Number: 085697 Clausing Metosa CNC Lathe Model: CNC-225 Serial Number: 49064 Milltronics CNC Lathe ML26 Model: ML26 Serial Number: 8535 Adjust X axis Gib to proper specifications Adjust X and Z Backlash through control software Check Squareness of Headstock and Tailstock Run check procedures for machine medium (C:>Drive), Hard Drive, Flash, Disk on Chip, etc. Check pump for proper operation, pressure etc. Clean Tank and Change Filter Inspect all way oil lines Change way oil manifolds or way oil injectors Check air regulator for leaks or faulty seals Check solenoids and air valves for leakage or malfunction Drain and clear water trap on air line filter Drain, clean and refill lubrication Check main pressure A TC Maintenance Remove covers and clean Check and adjust alignments Check slide and turret operation, and lubricate Check spindle belts Check spindle temperature and adjust chiller card Check chiller system and adjust, and clean pump filter, fill if necessary Check drawbar for proper retention and pressure at tool in/out (USE SVT0066) Check and adjust spindle tram Change Spindle Motor filter if applicable Check all connections, wires, boards, connectors etc. Check and adjust sin/cos on clock card (DC machines only) Check ground integrity Adjust position loop gain Check and clean all fans for proper operation Check and fill all fluid levels Check and adjust rigid tapping if applicable Check scales if applicable Advise on service items that need to be addressed MANUAL LATHE MACHINES Standard Modern Manual Lathe Model: 1725 Serial Number: 6598 Standard Modern Manual Lathe Model: 1334 MIL Serial Number: 12511 Adjust X axis Gib to proper specifications Adjust X and Z Backlash Check Squareness of Headstock and Tailstock Check pump for proper operation, pressure etc. Clean Tank and Change Filter Inspect all way oil lines Change way oil manifolds or way oil injectors Check air regulator for leaks or faulty seals Check solenoids and air valves for leakage or malfunction Drain and clear water trap on air line filter Drain, clean and refill lubrication Check main pressure ATC Maintenance Remove covers and clean Check and adjust alignments Check slide and turret operation, and lubricate Check spindle belts Check spindle temperature and adjust chiller card Check chiller system and adjust, and clean pump filter, fill if necessary Check drawbar for proper retention and pressure at tool in out (USE SVT0066) Check and adjust spindle tram Change Spindle Motor filter if applicable Check all connections, wires, boards, connectors etc... Check and adjust sin/cos on clock card (DC machines only) Check ground integrity Adjust position loop gain Check and clean all fans for proper operation Check and fill all fluid levels Check and adjust rigid tapping if applicable Check scales if applicable Advise on service items that need to be addressed CNC GRINDING MACHINES Hardinge CNC Surface Grinder Model: EZ-Surf Serial Number: 699EZ Clausing CNC Surface Grinder Model: CSG-1224 ASDII Serial Number: 30035171 Adjust Y and Z Backlash through control software Check Hydraulic Unit for proper pressures and adjust as needed Run Check Disk, Scandisk and De-Frag routines for machine HDD Check pump for proper operation, pressure etc. Clean Tank and Change Filter Inspect all way oil lines Change way oil manifolds or way oil injectors Check air regulator for leaks or faulty seals Check solenoids and air valves for leakage or malfunction Drain and clear water trap on air line filter Drain, clean and refill lubrication Check main pressure ATC Maintenance Remove covers and clean Check and adjust alignments Check slide and turret operation, and lubricate Check spindle belts Check spindle temperature and adjust chiller card Check chiller system and adjust, and clean pump filter, fill if necessary Check drawbar for proper retention and pressure at tool in/out (USE SVT0066) Check and adjust spindle tram Change Spindle Motor filter if applicable Check all connections, wires, boards, connectors etc. Check and adjust sin/cos on clock card (DC machines only) Check ground integrity Adjust position loop gain Check and clean all fans for proper operation Check and fill all fluid levels Check and adjust rigid tapping if applicable Check scales if applicable Advise on service items that need to be addressed MANUAL GRINDING MACHINE Myford Cylindrical Grinder Model: MG12 Serial Number: 171086 Adjust Y and Z Backlash Check Hydraulic Unit for proper pressures and adjust as needed Check pump for proper operation, pressure etc. Clean Tank and Change Filter Inspect all way oil lines Change way oil manifolds or way oil injectors Check air regulator for leaks or faulty seals Check solenoids and air valves for leakage or malfunction Drain and clear water trap on air line filter Drain, clean and refill lubrication Check main pressure ATC Maintenance Remove covers and clean Check and adjust alignments Check slide and turret operation, and lubricate Check spindle belts Check spindle temperature and adjust chiller card Check chiller system and adjust, and clean pump filter, fill if necessary Check drawbar for proper retention and pressure at tool in/out (USE SVT0066) Check and adjust spindle tram Change Spindle Motor filter if applicable Check all connections, wires, boards, Connectors etc. Check ground integrity Adjust position loop gain Check and clean all fans for proper operation Check and fill all fluid levels Check and adjust rigid tapping if applicable Check scales if applicable Advise on service items that need to be addressed
- Web Link
-
FBO.gov Permalink
(https://www.fbo.gov/spg/USA/NGB/DAHA06/W91ZRS12T0002/listing.html)
- Place of Performance
- Address: 11109 TASM-G 139 Tower Ave Groton CT
- Zip Code: 06340
- Zip Code: 06340
- Record
- SN02648645-W 20120106/120104234423-7dc4aa2225eda5e5578f7b11d029c6e8 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |