Loren Data's SAM Daily™

FBO DAILY ISSUE OF MAY 22, 2010 FBO #3101
SOLICITATION NOTICE

47 -- Replace Interior chill water pipe lagging (for mold abatement) ( shipboard)

Notice Date

5/20/2010
 

Notice Type

Combined Synopsis/Solicitation
 

NAICS

336611 — Ship Building and Repairing
 

Contracting Office

Department of Homeland Security, United States Coast Guard (USCG), USCG Base Support Unit New Orleans, 4640 Urquhart Street, New Orleans, Louisiana, 70117-4698, United States
 

ZIP Code

70117-4698
 

Solicitation Number

2110290DNC425
 

Archive Date

6/10/2010
 

Point of Contact

Alyssa Fedor, Phone: (504) 253-4521, Lyndie J. Loyd, Phone: 5042536446
 

E-Mail Address

Alyssa.P.Fedor@uscg.mil, Lyndie.J.Loyd@uscg.mil
(Alyssa.P.Fedor@uscg.mil, Lyndie.J.Loyd@uscg.mil)
 

Small Business Set-Aside

N/A
 

Description

Replace Interior chill water pipe lagging. For mold abatement 1. SCOPE 1.1 Scope. Remove existing insulation and renew to thickness specified below in table 1. 2. APPLICABLE DOCUMENTS SFLC Standard Specification 0000 January 2009 MIL-STD-769J, Thermal Insulation Requirements for Machinery and Piping MIL-A-24179, Jun 1987, Adhesive, Flexible Unicellular-Plastic Thermal Insulation Coast Guard Commandant Instruction (COMDTINST) M10360.3, Coatings and Color Manual Coast Guard Drawing 627 WMEC 512-002, Rev D, Vent Weather Covers and Louvers Coast Guard Drawing 627 WMEC 512-003, Rev C, Arrg%u2019t of Ventilation in Fan & Intake Rooms 1-63-1-Q, 1-63-2-Q & 1-108-0-Q Coast Guard Drawing 627 WMEC 512-011, Rev H, Arrangement Ventilation & Air Conditioning Main Deck Coast Guard Drawing 627 WMEC 514-001, Rev C, Diagram Heating and Chilled water system Coast Guard Drawing 627 WMEC 514-003, Rev D, Arrangment of Chilled and Hot Water System Outside of Machinery Space Coast Guard Drawing 627 WMEC 514-004, Rev C, Heating, Ventilation & Air Cond Control, Block & Schem Wrg Diagrams Electric Boat Corporation Specification No. 4013 (EB Spec 4013), Anti-Sweat and Refrigerant Insulation systems (Sheets and Tubes), Rev-A, February 16, 1999 NAVSEA Drawing 804-5959214, Rev-, Piping Insulation - Installation Details 3. REQUIREMENTS 3.1 Contractor to inspect the system in the presence of the CG inspector, verify the location and lengths of all piping to be re-insulated, and note the current condition of the insulation. 3.2 Contractor shall cut away and remove all insulation as identified by the CG inspector, not to exceed the linear footage in each compartment listed in Table 1. NOTE: One Week prior to start of work, contractor must provide CG inspector the name and technical data of the insulation product to ensure it is appropriate. 3.2 Interferences include but are not limited to: overhead piping, overheads, ventilation ducting, berthing area bedding, crew lockers, valves, sprinkler heads, and bulkheads. All of the Chill water piping to be re-insulated is located in the overhead area of the compartment. 3.3 New insulation installation. The Contractor shall furnish, cut, fit, and install new closed cell, halogen-free, foam insulation material, conforming to EB Spec 4013, to a thickness as specified in Table 1 (Insulation Particulars) below, over the exposed pipe surfaces, including associated fittings, as applicable; secure piping material with adhesive material conforming to MIL-A-24179, Type II, Class 1. Coat the newly installed insulation in accordance with COMDTINST M10360.3, using the coating system specified for %u201CInsulation Surfaces, Fiberglass Sheet/ Closed Cell PVC Foam%u201D in Table IB (Interior Coating Systems). Select color to match existing adjacent surfaces. This chill water piping normally carries water of a temperature 40 to 50 degrees Fahrenheit, k value of the insulation must be.250 Btu-ft/(hr-ft2-oF) or less within this temperature range. Product must be mold resistant. TABLE 1. INSULATION PARTICULARS Compartment Name and Number Piping Diameter Length to be insulated in linear feet Thickness required of new insulation Lower JO Passageway 2-76-0-L ½ inch 14ft 1 inch Officer Stateroom 2-84-1-L 2 inch 18ft 2 inch Engineer Berthing 2-52-01-L 1 inch 90ft 2 inch Engineer Berthing 2-52-01-L ½ inch 6ft 1 inch First Class berthing 2-32-01-L ½ inch 20ft 1 inch Main Passageway 1-52-01-L 1 inch 24ft 2 inch 3.4 If necessary for a vapor seal, Use sealant compatible with insulation and paint products to completely seal surface to exclude humidity and moisture intrusion. 4. QUALITY ASSURANCE 4.1 Contractor shall, in the presence of the CG inspector, optest the chill water system for 24 hours and check for condensation or failure of the insulation. 4.2 Contractor shall dispose of all materials in accordance with Federal, state and local laws.
 

Web Link

FBO.gov Permalink
(https://www.fbo.gov/spg/DHS/USCG/COUSCGISCNO/2110290DNC425/listing.html)
 

Place of Performance

Address: USCGC Deciisive, 100 Singing River Island, Pascagoula, Mississippi, 39595, United States

Zip Code: 39595
 

Record

SN02154893-W 20100522/100520234524-c82eb91e8e27e58c5dc36a197b8f0d43 (fbodaily.com)
 

Source

FedBizOpps Link to This Notice
(may not be valid after Archive Date)

---

| FSG Index  |  This Issue's Index  |  Today's FBO Daily Index Page |