SOLICITATION NOTICE
59 -- PAS-CRAN-403 Disconnect Switch Relocation, ECP-1693 - Request for Quote
- Notice Date
- 6/8/2009
- Notice Type
- Combined Synopsis/Solicitation
- NAICS
- 238210
— Electrical Contractors and Other Wiring Installation Contractors
- Contracting Office
- Department of the Army, U. S. Army Materiel Command, Anniston Chemical Agent Disposal Facility (ANCDF), 3580 MORRISVILLE ROAD, Anniston, Alabama, 36201, United States
- ZIP Code
- 36201
- Solicitation Number
- ANCDF-RFQ-WA9-2189
- Archive Date
- 6/30/2009
- Point of Contact
- John Danielson, Phone: 2562380721
- E-Mail Address
-
john.danielson@wancdf.com
(john.danielson@wancdf.com)
- Small Business Set-Aside
- N/A
- Description
- ANCDF-RFQ-WA9-2189 Provide all labor, materials to relocate the existing disconnect switch for PAS-CRAN-403 crane from the present location inside the Stack Monitor House to a location on the walkway at EL. 144'-3" directly below and within sight of the crane runway conductors. The scope of work includes, but is not limited to: Electrical: 1.1 Apply Lockout/Tag-outs to 50A circuit breaker for PAS-CRAN-403 in the existing SPS-MCC-111 480V MCC to ensure that all energy sources are removed for equipment that is to be worked on in accordance with WA procedure SAF-2.25. 1.2 Remove input, output power cables and conduits from the existing PAS-CRAN-403 disconnect switch located in stack monitor house 75-461. 1.3 Relocate the existing PAS-CRAN-403 disconnect switch from the present location inside the stack monitor house 75-461 to a location on the walkway at EL. 144'-3" directly below and within sight of the crane runway conductors. 1.4 Install 1-1/2"-inch conduit from the existing cable tray PT6-034 to the existing the disconnect switch located at new location (Column 5D). 1.5 Reroute existing cable in new 1-1/2" conduit to the disconnect switch located at new location (Column 5D) and terminate the cable as shown on attached WA Sketch No SK04-AN-6-E-509-SC and drawing AN-6-E-501-SC. 1.6 Install 1-1/2"-inch conduit from the existing Bridge Crane control box conduit to the existing the disconnect switch located at new location (Column 5D). 1.7 Reroute existing cable in new 1-1/2" conduit to the disconnect switch located at new location (Column 5D) and terminate the cable as shown on attached WA Sketch No SK04-AN-6-E-509-SC and drawing AN-6-E-501-SC. 1.8 Conductors shall be color coded or identified with phase tape as follows: Voltage Conductor Color 277/480V A Phase Brown B Phase Orange C Phase Yellow Ground Green 1.9 All wall penetrations shall be sealed. A sealing material such as "Fire Foam" should be employed. 1.10 All electrical connections shall be in accordance with NEC Article 110.14 1.11 After job has been completed, remove the LO/TO. General: 1. All testing and inspections to ensure that the final installation performs as designed.
- Web Link
-
FBO.gov Permalink
(https://www.fbo.gov/notices/3506ddd6e07dcee048f703b7595c5c58)
- Record
- SN01838691-W 20090610/090608234920-3506ddd6e07dcee048f703b7595c5c58 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |