SOLICITATION NOTICE
12 -- PARTS KIT
- Notice Date
- 2/25/2004
- Notice Type
- Solicitation Notice
- NAICS
- 336413
— Other Aircraft Parts and Auxiliary Equipment Manufacturing
- Contracting Office
- Defense Logistics Agency, Logistics Operations, Defense Supply Center Richmond, 8000 Jefferson Davis Highway, Richmond, VA, 23297-5000
- ZIP Code
- 23297-5000
- Solicitation Number
- SP0475-04-R-2906
- Response Due
- 4/27/2004
- Archive Date
- 5/12/2004
- Point of Contact
- Ronald Murrell, Contract Specialist (Contractor), Phone (804)279-5570, Fax (804)279-4505,
- E-Mail Address
-
rmurrell@dscr.dla.mil
- Small Business Set-Aside
- Total Small Business
- Description
- ITEM DESCRIPTION FOR PR: LTC04044018227 PARTS KIT,FUSELAGE EXCEPTIONS: 1. USE AFMC FORM 221 DTD 3/22/01 AS AN APPROVED PARTS LIST. NOTE:AWARDEE SHALL OBTAIN FITTING P/N 16RB5848-7 TAPER FILLER-9,-10,-11,-12, RADIUS BLOCKS -13,-1 FROM: PROGRESSIVE INC CAGE 64900 "EXCEPTIONS"TO DWG 9825018-10 AS NOTED: SPECIAL INSTRUCTIONS FOR NSN 1560-01-458-5514 PART NUMBER 9825018-10 ENGINEERING DATA REQUIREMENTS DTD 26 APR 01. 1. THE FOLLOWING SPECIFICATIONS/STANDARDS, ETC., WILL BE USED IN LIEU OF THE DATA INDICATED. THE SUPERSEDED DATA WILL NOT BE FURNISHED UNLESS SO INDICATED. 1.1 PENETRANT INSPECT PER ASTM E1417, TYPE I, LEVEL 2, METHOD B PER SAE AMS 2644 IN LIEU OF NDTS-1101. NOTE: ONLY THOSE FACILITIES THAT HAVE SUCCESSFULLY COMPLETED THE PRODUCTION PENETRANT DEMONSTRATION PROGRAM AN ARE LISTED IN THE CURRENT REVISION OF FQPL-1101 CAN PERFORM NDTS-1101 INSPECTION TO ZONES 1A, 1B, 1C. THE FOLLOWING ACCEPTANCE/REJECTION CRITERIA WILL BE USED FOR ALL OTHER ZONES AS LISTED BELOW. (1) ZONE 0 AND ZONE 1 ROUNDED DISCONTINUITIES EQUAL TO OR EXCEEDING 0.02 INCHES SHALL BE REJECTED. (2) ZONE 2 (EXCEPT FOR CAST SURFACES) ROUNDED DISCONTINUITIES EQUAL TO OR EXCEEDING 0.03 INCHES SHALL BE REJECTED. (3) ZONE 2 (CAST SURFACES) ROUNDED DISCONTINUITY EQUAL TO OR EXCEEDING 0.03 INCHES SHALL BE REJECTED. (4) ZONE 3 THIS ZONE HAS BEEN RESERVED FOR FUTURE USE. (5) ZONE 4 THIS ZONE IS INTENDED FOR INSPECTION OF RAW MATERIALS SURFACES, I.E. AS FORGED, AS ROLLED, ETC. DISCONTINUITIES RESULTING FROM SURFACE IMPERFECTIONS WHICH ARE PERMITTED BY THE PROCUREMENT SPECIFICATION ARE ACCEPTABLE. (6) ZONE 5 THIS ZONE IS INTENDED FOR AREAS WHERE SUBSEQUENT PROCESSING SUCH AS MACHINING, ETCHING, GRINDING, ETC., WILL BE USED TO REMOVE SURFACE MATERIAL. DISCONTINUITIES RESULTING FROM ROUGH SURFACES, MINOR PITTING, ETC., SHALL NOT BE CAUSE FOR REJECTION PROVIDING THE CONDITIONS ARE REMOVABLE WITHIN DRAWING TOLERANCES. (7) ZONE 6 THIS ZONE IS INTENDED FOR AS-CASE SURFACES WHICH REMAIN ON THE FINISHED PART OF AIRCRAFT QUALITY CASTINGS. USE THE ACCEPT/REJECT CRITERIA AS FOR ZONE 2 (CAST SURFACES). NOTES: WHEN NO ZONE NUMBER IS SPECIFIED ON THE ENGINEERING DRAWING, ZONE 0 SHALL BE USED AS ACCEPT/REJECT CRITERIA FOR ROUNDED DISCONTINUITIES. LINEAR DEFECTS ARE NOT ALLOWED WHETHER VISIBLE UNDER WHITE OR BLACK LIGHT. LINEAR INDICATIONS ARE LINEAR IN SHAPE AND HAVE A LENGTH THREE TIMES OR GREATER THAN THE WIDTH. FOR A ROUNDED INDICATION TO BE REJECTABLE, IT MUST BE VISIBLE UNDER BLACK LIGHT. FOR DISCONTINUITIES THAT TOUCH THE CONGLOMERATE SIZE SHALL BE CONSIDERED AS ONE DISCONTINUITY. DISCONTINUITIES WHOSE SEPARATION DISTANCE IS EQUAL TO OR CLOSER THAN ZONE CRITERIA SIZE AND WHICH ARE VISIBLE UNDER BLACK LIGHT, SHALL BE REJECTED REGARDLESS OF INDIVIDUAL SIZE. 1.2 MARK PER MIL-STD-130 IN LIEU OF FPS-3008. 1.3 FINISH SPECIFICATIONS 16PR070 AND FPS 3001 ARE NOT FURNISHED, FINISH PER THE FOLLOWING: 1.4 -9, -10 TAPERED FILLER, -13, -15 RADIUS BLOCK. 1.4.1 CLEAN WITH MILD ABRASIVES AND CHROMIC ANODIZE ALL SURFACES PER MIL-A-8625, TYPE I. A. IF ELECTRICAL BONDING IS REQUIRED ON SPECIFIED AREAS BY REFERENCE TO FPS-3024, ANODIZE ONLY THOSE SURFACES NOT SPECIFIED FOR ELECTRICAL BONDING. PREPARE SURFACES SPECIFIED FOR ELECTRICAL BONDING PER MIL-C-5541 CLASS 3. B. AFTER ANODIZE, INSPECT ANODIZED SURFACES FOR DARKENED AREAS OF DISCOLORATION WHICH MAY INDICATE SOFT MATERIAL. PARTS CONTAINING SUCH SPOTS SHALL MEET THE REQUIREMENTS OF NDTS 1500 PRIOR TO ANODIZE COATING ACCEPTANCE. 1.4.2 APPLY TWO COATS OF MIL-PRF-85582 PRIMER TO SPECIFIED SURFACE. 1.4.3 APPLY MIL-C-27725, TYPE II, GRADE A OR B, FUEL TANK COATING ON SPECIFIED SURFACES PER FPS-1004. 1.5 -11, -12 TAPERED FILLER. 1.5.1 APPLY MIL-C-27725, TYPE II, GRADE A OR B, FUEL TANK COATING ON SPECIFIED SURFACES PER FPS-1004. 1.6 -7 FITTING 1.6.1 CLEAN WITH MILD ABRASIVES AND CHROMIC ANODIZE ALL SURFACES PER MIL-A-8625, TYPE I. 1. IF ELECTRICAL BONDING IS REQUIRED ON SPECIFIED AREAS BY REFERENCE TO FPS-3024, ANODIZE ONLY THOSE SURFACES NOT SPECIFIED FOR ELECTRICAL BONDING. PREPARE SURFACES SPECIFIED FOR ELECTRICAL BONDING PER MIL-C-5541 CLASS 3. 2. AFTER ANODIZE, INSPECT ANODIZED SURFACES FOR DARKENED AREAS OF DISCOLORATION WHICH MAY INDICATE SOFT MATERIAL. PARTS CONTAINING SUCH SPOTS SHALL MEET THE REQUIREMENTS OF NDTS-1500 PRIOR TO ANODIZE COATING ACCEPTANCE. 1.6.2 APPLY TWO COATS OF MIL-PRF-85582 PRIMER ON BOTTOM AND FORWARD EXPOSED SURFACES ONLY. 2.0 THE SOURCES IF LISTED ON THE C AND P STANDARDS ARE THE ONLY APPROVED SOURCES FOR THOSE ITEMS. SUBSTITUTE SOURCE OR PART APPROVAL BY THE COGNIZANT ENGINEERING ACTIVITY. 3.0 THE KIT REQUIRES A -7 FITTING. THE QUALIFIED SOURCE FOR THE -7 FITTING IS PROGRESSIVE INC 1030 COMMERCIAL BLVD N ARLINGTON, TX 76001, 7197 PHONE (817) 465-3221 AFMC FORM 221 DATED 22 MARCH 2001. FSCM MFR P/N NOUN QTY 81755 16RB5848-15 RAD BLK 2 81755 16RB5848-13 RAD BLK 10 81755 16RB5848-12 TAP. FILLER 1 81755 16RB5848-11 TAP. FILLER 1 81755 16RB5848-10 TAP. FILLER 1 81755 16RB5848-9 TAP. FILLER 1 81755 16RB5848-7 FITTING 1 88730 P5055-1-6 CLOTH 1 YD ... END OF KITS PARTS LIST... MARK IAW MIL-STD-130K, DATED 15 JAN 00. CONFIGURATION CONTROL APPLIES SEE CLAUSE 52.246-9G36 (SECTION I). TECH DATA PKG AVAILABILITY: AN "EXPORT CONTROL" TECHNICAL DATA PACKAGE (TDP EXISTS FOR THIS NSN. TECHNICAL DATA WILL ONLY BE RELEASED TO CONTRACTORS AUTHORIZED/CERTIFIED BY DEFENSE LOGISTICS SERVICE CENTER. CERTIFIED REQUESTORS SHOULD SUBMIT TDP REQUESTS TO DSCR VIA INTERNET. THE INTERNET ADDRESS IS HTTP://WWW.DSCR.DLA.MIL/TDMD (ALL IN LOWERCASE, PLEASE). IF CERTIFICATION IS REQUIRED, REQUEST A DD FORM 2345, MILITARY CRITICAL TECHNICAL DATA AGREEMENT, FROM DEFENSE LOGISTICS SERVICES CENTER, DLSC-FBA, FEDERAL CENTER, BATTLE CREEK, MICHIGAN 49017-3084. WWW.DLIS.DLA.MIL FIRST ARTICLE/PREPRODUCTION APPROVAL REQUIRED, GOVERNMENT VERIFICATION OF: VERIFICATION OF MATERIAL CERTIFICATIONS, PART NUMBERS, QUANTITY OF EACH PART THAT IS REQUIRED, NOMENCLATURE, AND SOURCE AS LISTED ON SPARES CONFIGURATION KIT LIST. FIRST ARTICLE EXHIBIT AND MATERIAL CERTIFICATIONS SHALL BE SENT TO: OO-ALC/MADLV (DODAAC FB2029) ATTN: DEAR JOHN BAY, BLDG 849W HILL AFB, UT 84056-5713 MARK FOR: FIRST ARTICLE FOR INSPECTION AND TEST. DO NOT POST. ATTN: CONTRACTOR AND SERVICE ACTIVITY TEST MONITIOR........................................ DISAPPROVED FIRST ARTICLE(S) SHALL BE RETURNED TO THE CONTRACTOR AT THE CONTRACTOR'S EXPENSE. APPROVED AND CONDITIONALLY APPROVED FIRST ARTICLE(S) SHALL BE RETAINED AT THE SERVICE TEST ACTIVITY UNTIL DISPOSITION INSTRUCTIONS ARE RECEIVED FROM THE PCO. IF DISPOSITION INSTRUCTIONS ARE NOT RECEIVED WITHIN 30 DAYS AFTER PROVIDING THE FIRST ARTICLE TEST REPORT TO DSCR, REQUEST THAT THE DSCR QA SPECIALIST BE NOTIFIED....................... CRITICAL APPLICATION ITEM I/A/W DRAWING NR 13873 014585514-02232 BASIC DTD 08/20/02 AMEND NR DTD TYPE NUMBER I/A/W QAP 13873 QAP-008 REFNO DTD 06/01/97 AMEND NR DTD TYPE NUMBER I/A/W DRAWING NR 98747 9825018 BASIC DTD 01/26/98 AMEND NR A DTD 10/12/99 TYPE NUMBER -10 Requirement is for an Indefinite Quantity Contract. This RFP will be issued as a Small Business Set-Aside. No Electronic Bulletin Board (EBB) or Internet Quoting Services (IQS) proposals will be accepted for this solicitation. Automated Best Value System (ABVS) applies. Proposals will be based on the Estimated Annual Demand quantity 18 each for the base year and 36 each for the four option years. Award will be based upon a combination of delivery, price, past performance, and other evaluation factors as described in the solicitation with delivery and price being more important. A copy of the solicitation will be available via the DLA Procurement Gateway at http://progate.daps.mil/home or http://12.3.216.20/home on the issue date cited in the RFP. From the Gateway homepage, select "Search RFPs" from the left-hand sidebar. Then choose the RFP you wish to download. RFPs are in Portable Document Format (PDF). To download and view these documents you will need the latest version of Adobe Acrobat Reader. This software is available free at http://www.adobe.com. A paper copy of this solicitation will not be available to requesters. The anticipated issue date is March 18, 2004.
- Record
- SN00530451-W 20040227/040225221841 (fbodaily.com)
- Source
-
FedBizOpps.gov Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |